How to change a zipper slider on a bag. How to put a zipper on a dog: an independent solution to the problem. How to put a zipper dog on

Undoubtedly, the zipper is one of the most convenient and practical locks. It's sad to see it break. What to do? You can take your clothes to a tailor and they will replace the entire zipper. But often you can simply change the slider (pawl). You can do this at home yourself. Below you will find instructions on how to fix different kinds lightning

Determining the cause of the defect

If the teeth are broken - then nothing can be done to help - it is necessary. If the teeth are fine, but the pawl gets stuck or the lock comes apart, then the problem is in the slider. Perhaps crimping the runner with pliers will help for a while. But, if this does not work, the dog must be replaced.

Type of lock, selecting a replacement

Types of lightning:

tractor, plastic teeth, the dog will be in the shape of a trefoil or oval
metal, triangular slider
twisted, oval runner

In addition, the size of the slider is important - most often it can be read on back side clamp Next to the size numbers there may be letters:

X – cast zipper, two-lock
L – does not open at the end, single-lock
H – one-piece zipper, two-way
D – clasp opens at the end, double-lock
A - one-piece
B – detachable with single lock
C – detachable with two-lock

Types of runners:

automatic - it doesn’t matter whether the tongue is lowered or not - the mechanism always blocks the inadvertent divergence of the teeth.
semi-automatic - when the zipper is closed, you need to lower the tongue. Otherwise, the lock may come apart.
haberdashery - does not have a lock. Great for bags and other items where there is not a lot of stress on the zipper.

We prepare the tools necessary for repairs

For repair you will need:

pliers
scissors
needle and thread
dog
limiter
some glue

Remove the limiter. If the stopper catches part of the fabric, pry up this edge with scissors.
Cut through the thickened edge. Otherwise it will be difficult to remove the old lock. You can’t forcefully pull out the old lock - you can break the teeth. Carefully remove the slider.
Reconnect the zipper and put on the new slider. Check if he walks well.
Sew the cut with an overlock stitch.

The plastic limiter will have to be replaced with a new one. The metal limiter can be carefully removed and put back in place. In order for the dog to stand up easily, you will need to slightly unclench it with pliers. Reinstall the limiter only when you are sure that the pawl is working.

We put the slider on the twisted zipper

The procedure is exactly the same. The actions are similar to changing the pawl on a regular detachable zipper. However, a twisted zipper has an advantage - it can be fastened in any direction. Therefore, for such a zipper you can install two sliders at once. Please note that they need to be placed on both sides - they must move towards each other.

Repairing a permanent zipper

The replacement principle is the same. However, you must first carefully unravel the seam to get to the edge of the zipper tape. After replacing the pawl, the seam must be laid again. Preferably on sewing machine- this way the thing will look neat. .

A final note:

If the mechanism is prevented from working by worn-out material, which the slider touches, apply glue to the frayed fabric. Using a needle, you can thinly coat the fabric between the teeth. Glue should not get on the teeth. Otherwise the lock will stop working.

If you do not want to waste time inserting the slider into the zipper, then you can contact us. Our specialists will solve your problem. For more detailed information call us by phone.

You can also watch a detailed video on how to properly insert the pawl into a zipper.

Joy of Ownership new thing sometimes marred by a broken slider. Locks fail with enviable regularity. Regardless of how long it has been in use, plastic or iron teeth crumble. But still, lightning often becomes unusable due to the slider.

The so-called “dog” jumps off one slider on the one-piece lock, or becomes deformed, or the body breaks completely. Is it enough to fix the slider or do I need to replace the entire zipper?

In this case, without professional help is not possible, since the lock has a complex technology of insertion. You may need to open up machine seams or even an overlocked edge.

It is much easier to replace a slider that has come off from a zipper with minimal skills and necessary tools. In certain situations, you have to fix the damage in order to put the item on. Since manufacturers have been saving on fittings lately, it is advisable to know how to insert the zipper pawl yourself.

Type of failure

If the lock has lost its teeth, the entire zipper needs to be replaced. It will close, but due to the loss of parts, reliability is highly questionable. The lock will keep opening and the teeth will continue to fall out. In this case, it is better to purchase a new clasp good quality and contact a professional studio.

The pawl requires replacement if the lock comes apart after closing. Sometimes the slider will have to be repaired if the fastener is stuck or does not fit tightly on the sliders.

Zipper type

How to repair a lock depends on the type of zipper, whether it is open or closed. Split zippers can be seen on jackets and coats. These are fasteners that are separated at the ends.

Closed fasteners are attached on both sides and are used on a bag or boots. Some closed fasteners are only secured on one side. This type is used for jeans, trousers, skirts.

Repair methods

If the slider has fallen off the open zipper on the jacket, then the fastener on the lock (this is a larger tooth that closes the slider) will not suitable size. The purpose of the fastener is to prevent the slider from flying out. In this case, you should pull out the fastener and put the lock in place.

The fixer itself is made from a thick piece of fabric that matches the color of the main fabric. To do this, depending on the size of the item on which the fastener is installed, you will need to cut a strip of fabric and carefully sew it onto the edge of the slider so that it prevents the lock from sliding.

If the slider has slipped from the slider on a closed zipper, and there are no damaged teeth, then most likely it has broken or become deformed. In this case, you should reinsert the pawl onto the slider and lightly press the body with pliers. This is a temporary measure. Such a zipper will not last long and it is better to remove the pawl in the near future and replace it.

What should I do if the slider is not deformed and cannot be inserted into the slider? In this case, as close to the edge as possible with the blade or nail scissors two or three cloves are pulled out. Pass the zipper pawl onto a flat strip of fabric, and carefully secure the resulting gap with a hidden stitch using a double thread to match the main fabric.

The zipper on jeans is repaired in the same way. If the dog has fallen off the slider, it is better to remove the teeth from below, from the side attached to the seam, since in this way the repair will not be noticeable. In the same way, the teeth are removed, the slider is hooked onto the slider, and when closed, the zipper is secured with threads.

In some cases, additional fastening is done with glue. But this takes time and skill. Super glue or PVA will do. Apply glue to the place on the zipper where the teeth were removed. However, before this, the lock is treated with a degreaser.

Acetone or alcohol will do. A cotton swab is dipped into the liquid and the attachment site is treated. When it dries, you should drop some glue and let it dry. If the consistency of the glue is liquid, then another layer will be required.

If the pulley on a detachable zipper, which itself is intact and unharmed, breaks, you just need to select a suitable slider and replace it. Tools you will need:

needle;
thread;
pliers.

The new slider is put on the zipper strip on which the socket is located. If you had to remove the limiter to do this, then it is better to either make a new one or reattach the old one. On the other side of the zipper, unauthorized sliding is protected by a fabric stopper. If this is not the case, then it will install itself.

The fixer is even easier to make using thread and a needle. A bartack is placed in the required place with several stitches so that they prevent the slider from falling out.

You can also repair a one-piece zipper puller yourself without having to completely replace the lock. To do this, just open the ends of the rails and insert the slider. The slider must be moved down.

The slots should be pressed with pliers until required size. If the movement of the pawl is difficult, then it is better to bend the slots slightly, while pressing carefully so as not to break the body.

Once the slider is installed, but movement on the rails seems difficult, you can resort to the old method of waxing the lock or laundry soap. After this, it is enough to slightly drive the dog along the zipper, and the serviceability of the lock is guaranteed.

These are simple manipulations that anyone can do, regardless of their skills. The recommendations will allow you, if necessary, not to run to the studio, but to quickly and independently fix the problem.

Obviously, the zipper type fastener is known to everyone and is very popular in all its applications and manifestations.

These are clothes and shoes, bags and cases, and a lot of other equally useful things. Do you know what underlies its operating principle?

Few people know that the idea for its implementation was given to the world by an ordinary bird. More precisely, a bird's feather. Even more precisely, the principle of connecting the elements of the pen into a single plane. This is an alternating interlocking of feather fibers, ultimately forming a single whole.
The same thing happens in ordinary “lightning”. When it is fastened, the elements of one edge engage with the elements of the other edge using a lock or, in other words, a “slider”. The elements can be plastic or metal staples or teeth, one end attached to a strip of fabric. The plastic version can be molded (called a “tractor”) or twisted (“spiral”).

The weakest link of this entire fastening device is usually the lock, or “slider”. Its malfunction can manifest itself in the breakdown of the “tongue” - the device that we pinch with our fingers. The mechanism that holds the slider closed may break, and then it will come unfastened. In addition, the malfunction can manifest itself in the divergence of the halves of the zipper when trying to fasten it. In the latter case, many advise pressing the halves of the lock closer to each other.

Repairing a zipper by pressing the slider

First, you can try to tighten the lock without removing the slider.

Find pliers, you can use wire cutters, or even a hammer

Find a place near the fastener where the interior space is empty and not where there is a partition. This is the part closer to the bottom of the jacket, as a rule.

Try to squeeze this edge with pliers until the upper and lower walls touch each other.

When you release the pliers, you will see that the edges will move back to some distance, but less.

Try checking the zipper fastening, if it starts to fasten, then everything is fine...

koposhilki.ru

If the zipper is still not fastened very well, then you will have to remove the slider...

To remove a faulty lock, you must remove the stopper on one or both halves of the fasteners. On one - if the zipper has a detachable connection at the bottom. The limiter is most often a metal bracket that prevents the “dog” from jumping out of the serrated tape.

This staple will need to be carefully bent using an awl or a thin screwdriver and completely removed from the strip of zipper base fabric.

After the limiter is removed, the slider is removed through the top of the zipper. We see that it is really distorted and therefore the lightning does not work...

We clamp the slider with pliers and correct its curvature.

Press on one side and the other

The corrected slider is placed on a zipper

Replace the limiter

And clamp it with pliers.

Checking to see if the zipper is fastened...

ladyzest.com

It happens that there is no limiter on the zipper, and the limiter is the bend of the fastener fabric followed by stitching. In this case, the edge needs to be trimmed. If this is difficult to do, then you can proceed as follows:

We will need small pliers (or manicure tongs, or a flathead screwdriver) and large pliers

Insert the flat end of a tool (screwdriver, for example) under the clamp of the slider and slightly press it out,

So that it can be easily removed from the zipper.

Insert the pliers into the slider as shown here to widen it a little.

Just don't overdo it, or you'll completely break it.

Then we insert the zipper slider again...

After such manipulations, the castle simply has to work :o)

Replacing the zipper slider

Pressing the lock, of course, is useful...
But such resuscitation can be carried out only once; the castle will not withstand any more and will completely fall apart. Therefore, if you managed to save your zipper once, then try to prepare a spare slider - just in case of a fire.

It is possible to qualitatively repair such a fastener on clothing or shoes without completely replacing it, only by replacing the entire lock. Even on a high-quality fastener, it fails first, since constant physical force is applied to it, and its area is relatively small compared to the area of all the teeth.

To determine which lock you need to purchase, you need to know several parameters. Look at the back of your “dog” and remember the number that is stamped there. These can be numbers 3, 4, 5, 6, 7, 8, 10, which indicate the width of the fastener in millimeters.

Determine the type of lock: it can be automatic - the mechanism that will prevent the clasp from unfastening in any position is located inside; semi-automatic - unfastening is possible only with the “tongue” raised; haberdashery - when the zipper teeth are not blocked and there is no stopper in the mechanism.

It must be remembered that the sliders change on metal and plastic zippers outerwear. On trousers and skirts, replacing the dog due to its specificity is impossible.
The zipper opens and the slider remains on one half of the zipper. The upper limiter is carefully removed using a screwdriver and pliers. If the edge of the zipper next to the stopper is very close to the fabric, you will need to trim it a little (this is rare).
You need to try to fasten the zipper itself. After this, without much effort, completely remove the lock from the side of the removed limiters. Install the new lock in place of the old one, tucking the edges of the guide tape into the pawl grooves. After the lock is installed, use pliers to clamp the metal stops into place or sew on the torn fabric.

Replacing a jacket's zipper slider

Replacing the slider with your own hands at home is not difficult and anyone can do the job.

The first step is to buy a slider of the required size, shape and suitable color in a sewing accessories store. The slider should be replaced with exactly the same one. If the color of the slider can be neglected, then the performance of the fastener will depend on the size and shape. Pay attention to the shape of the slider - it should match the old model. There are three main types of zippers: spiral, tractor, and metal. You should not put a “tractor” lock on a spiral or metal snake and vice versa. The same goes for the slider size.

In order not to make a mistake when buying a slider, you should have an “old” sample of the “zipper” on hand. For ease of fitting, you need to remove the old slider from the zipper. To do this, carefully remove the stoppers at the top of the zipper using side cutters or pliers and carefully remove the lock.

In addition to the slider, we will need new iron stops. They can be easily removed from old zippers using any sharp object (knife, etc.) - you just need to bend the teeth of the stopper and carefully pull the zippers out of the fabric.

When the slider and limiters have been selected or purchased, we will begin the alteration. Installing a new slider. Then we insert the limiters and clamp them with pliers.

If you need to replace the slider on children's clothing, but there are no suitable stoppers at hand, you can make them from threads - sew several stitches in one place, simulating a stopper.

This completes the replacement of the zipper slider. It turned out that there is nothing complicated in such a change.

B — detachable zipper with 1 lock. How to change a broken zipper? H – one-piece zipper with 2 locks. You can try installing a slider on a plastic tractor zipper without removing the upper stops.

Change clothes and take the item to the studio? In most cases, it is enough to replace the pawl and wear the item again. But not everyone knows how to quickly fix a zipper pull. To change the slider, you need to know what types of sliders there are and what to do if they break. If the teeth on the zipper have crumbled, then the lock itself needs to be changed completely. When do you have to think about how to replace a zipper dog?

It is impossible to solve the problem of how to make a zipper if the lock does not fit under it. Thread the second half of the lock into the slider, check how it closes the teeth, then install the limiter, pressing it with pliers. Instead of a limiter, you can install 2 sliders that can move freely in both directions. When replacing the slider, you need to move it very smoothly.

Zip slider

If the teeth are plastic, then even after you have completed the task of putting the zipper on your own, the lock will not last long. A stopper, which can be purchased at a store, or can be replaced with several large stitches, will prevent the runner from slipping off.

How to put a new zipper on a zipper that is already starting to wear out? Here are some of the letter indices printed on the back of the sliders. A - one-piece zipper. L - One-piece clasp with 1 lock. This information is necessary only for lightning manufacturers. It does not affect the replacement of sliders - runners, since the sizes of the zipper links are standard. Another reason is wear of the slider jumper due to friction against the teeth of the zipper, both on metal and plastic zippers.

How to put a dog on a twisted zipper?

The slider needs to be replaced. 3, 5, 8, 10) First of all, remove the stopper (usually on the right side of the zipper) using a side cutter, without damaging the zipper tape. Then we put on the slider at a slight angle (in no case should you apply a lot of force, so as not to damage the slider or zipper teeth).

We connect both halves of the zipper and check how the slider fastens the zipper. Before removing the top stop, carefully inspect the zipper) Replacing the slider (slider) is done in the same way as on a metal zipper. The technique for replacing the slider/runner is described above; you won’t add anything new. Removable without damaging the zipper spiral and tape. Bend the stopper with pliers and secure it to the zipper.

When installing sliders on two-way zippers, sliders - sliders should be installed in different directions of movement. Recently, zippers with upper limiters made of sealed plastic have appeared. To prevent destruction of this part of the zipper, it should be periodically treated with Moment type glue. Using a sewing needle, having previously dipped it in glue, carefully coat the damaged area, and with the same needle smooth out the applied glue. Effective method prolongation of lightning operation.

Replacing the slider yourself is easy and simple

Align both sides of the zipper as carefully as possible. Clamping it with pliers from above (the inner surface of the plier should touch outside slider), carefully insert the detached half of the zipper into the slider.

If not, then drag the slider as close to the end as possible. You will have to choose where the closing clasp will start. Using a good pair of scissors, make a slit on the half of the zipper without the slider, at the same level as the bottom of the slider when it is in its lowest position.

If the zipper just opens something and it doesn’t matter which way it opens (not like, for example, a fly), you can try this method. Pull the clasp to close the zipper. You can seriously damage the zipper if you pull too hard to pick up the slack. In step 2, you can make a cut flush with the top of the runner to minimize sagging.

When you force the disconnected half back into the slider with pliers, the teeth on the normal half can be damaged. It will then be impossible to zip the zipper further than this connection point. Use only if you can avoid tearing the fabric. If the item is quite expensive and you do not want to take risks, it is better to completely change the zipper. The method will not work on zippers that separate all the way, like on jackets.

This one is for “twisted” zipper No. 7, it has teeth in the shape of a spiral. Everyone has encountered the problem when the zipper on a jacket or sweater “spreads” or the slider breaks (popularly called the “dog”).