Characteristics of the work. Repair, assembly and testing of simple electrical units and aircraft parts. Soldering and desoldering of aircraft parts and assemblies in simple units, performing the necessary plumbing operations. Determining the main faults of parts of electrical equipment being repaired and eliminating them. Determination of the completeness of electrical equipment removed from the aircraft. Preparation and selection of parts for the assembly of electrical units. Taking measurements in circuits direct current using electrical measuring instruments (ammeter, voltmeter, ohmmeter, tester) and simple installations, semi-assembly and wiring diagrams and technical documentation.

Must know: the purpose, principle of operation and design of simple electrical units; technology for disassembling, cleaning and assembling electrical units; technical specifications for repair of electrical units; basic information about the materials used in the repair of serviced equipment; soldering technology; the purpose and rules for the use of testing installations, devices, instrumentation and power sources located at the serviced production site; basics of electrical engineering, electromechanics and plumbing; rules for reading drawings and diagrams.

Work examples

1. Signal fittings lighting fixtures type SLTs, SLM, SLSH, VLS, KPS - disassembly, assembly, inspection.

2. Fuse holders type PM, DP, VP, PV - repair.

3. Contact blocks - disassembly, replacement, assembly.

4. Limit switches - repair, assembly, testing.

5. Shock-absorbing panels, platforms and brackets for fastening equipment - repair and installation.

6. Lampshades type PPS, PSG, PSSO - assembly and installation.

7. Sockets and plugs - repair, replacement, inspection.

8. Sirens, bells type C, ZP, LUN - inspection, repair, assembly.

§ 236. Electrician for testing and repair of electrical equipment (4th category)

Characteristics of the work. Disassembly, repair, assembly and adjustment medium difficulty electrical units. Determination of the technical condition of the elements included in the electrical mechanism. Troubleshooting electrical mechanisms that require plumbing work. Repair of electrical harnesses of medium complexity with sealing of tips and soldering of plug connectors. Determining the condition of electrical wires using electrical measuring instruments. Testing of simple electrical equipment using special stands and installations. Preparation of repair cards.

Must know: the design of aircraft being repaired; design, purpose, principle of operation, installation and fastening locations of the devices, electrical mechanisms and equipment used; technology for repair and regulation of electrical equipment; rules for checking the insulation resistance of electrical wires; basic information about the brands, purpose and properties of materials used in electrical equipment, as well as during its repair; basic information about the system of tolerances and fits, surface treatment parameters; electrical and kinematic diagrams of electrical units being repaired; methods for testing electrical units and their parts on test benches; design of electrical measuring instruments used and rules for their use; basic laws of electrical engineering, electronics; technical and working documentation; plumbing in the scope of work performed.

Work examples

1. Automatic machines such as AVP, AB, AVD, AMO - disassembly, repair, assembly.

2. Ammeters type A, AF - repair, regulation.

3. BPS type blocks - repair.

4. Voltmeters type VP, EV, VF, VA, LUN - repair, regulation.

5. Brake release sensors - disassembly, repair, assembly.

6. ZM type locks - repair, adjustment, assembly.

7. Ignition coils type SK, KNA, KMB, KR - repair with installation in units.

8. Pneumatic switches type UP - repair, regulation.

9. Electric hydraulic cranes type GA - repair, regulation.

10. Electric heaters, air heaters - repair, assembly, regulation.

§ 237. Electrician for testing and repair of electrical equipment (5th category)

Characteristics of the work. Repair, assembly, regulation, testing and fault detection of electrical units of medium complexity, testing them under voltage on an aircraft. Carrying out work on balancing the armatures of generators and electric motors. Dismantling of complex electrical units. Determination of the technical condition of electrical equipment being repaired. Assembly and installation of devices and small installations for regulating and testing electrical units. Calibration and calibration of electrical equipment. Detection of malfunctions of operating devices and installations. Calculation of parameters of heating devices. Carrying out the necessary plumbing and soldering work.

Must know: the design, purpose, operating principle of the electrical equipment being repaired; technology for disassembling, repairing, assembling, regulating and testing electrical units being repaired; technical specifications for repaired electrical units and electrical appliances; methods for identifying and eliminating major faults in electrical equipment being repaired; methodology for regulating and checking equipment being repaired; operating principle of generators, electric motors, switching equipment; basics of electrical engineering, mechanics, photographic engineering.

Work examples

1. Automatic circuit breakers of the AZP type - repair, testing.

2. Contactor units of the APT type - repair, regulation, testing.

3. Transformer units - testing, replacement.

4. Blocks and elements of systems such as BTT, BUK, BUSO, BIF, IPO - repair, fine-tuning, testing.

5. Rectifier devices - repair, testing under current.

6. Generators type VG, GSK, GSN, GSP - repair, assembly, testing.

7. Engine automatic transmission manifolds - repair, assembly, testing.

8. Micromachines of tracking systems type SS, VD - repair.

9. Panels of power units, simulation and control panels, LUN type consoles - inspection and repair.

10. Brake parachute release control systems - inspection, repair, testing.

11. Photocontrol devices such as FKP, PAU - assembly, testing.

§ 238. Electrician for testing and repair of electrical equipment (6th category)

Characteristics of the work. Repair, assembly, regulation, testing and fault detection of complex electrical units and automatic devices aircraft. Determination of the degree of suitability of complex electrical equipment. Making decisions and choosing a method for troubleshooting electrical equipment. Using the reference book, perform calculations of the parameters of individual sections of electrical circuits. Carrying out plumbing and finishing work for 6 - 7 qualifications with soldering of electrical elements when repairing complex electrical mechanisms. Identification and elimination of electrical equipment faults. Preparation of forms and certificates.

Must know: the purpose, design, principle of operation and operating rules of control equipment for electrical mechanisms and motors; technology for repair, assembly, regulation and fine-tuning of complex electrical equipment; types, causes, methods of identifying and eliminating faults; types of anti-corrosion and paint coatings; basic information about the rules and procedures for certification of electrical products; rules for using measuring equipment; fundamentals of electromechanics, automatic control, photographic equipment.

Work examples

1. Control equipment type KPR, KOCH - fine-tuning, testing.

2. Blocks and elements of systems such as BA, BAR, BDU, BOG, BOCH, BOP, ADS, MVD, UVV - defect detection, repair, testing.

3. Generators type GT, GS, STS, SGS, SGK - repair, regulation, testing.

4. Hertzmeters type GF, ChF - repair, testing.

5. Boards, remote controls, shields with SR more than 20 pins - repair, adjustment, testing.

6. Compressors, air conditioners - repair, testing.

7. Distribution boxes, central switchgear of engine nacelles left and right - repair with wiring and testing.

8. Air starters - repair, debugging, regulation, testing.

9. Transformers of high-voltage, pulse and high-frequency systems - repair, testing.

10. Headlights type LFSV, MPRF, PRF, FBV - repair, testing.

11. Filter ventilation units - repair, testing.

12. Electric motors of the MTG, EPV, EPK, MGV, MGU, MRT types - repair, debugging, testing.

§ 239. Electrician for testing and repair of electrical equipment (7th category)

Characteristics of the work. Repair, adjustment and fine-tuning of complex systems and units of electrical equipment of aircraft, ensuring their output to the specified operating parameters. Assembly according to drawings of complex test installations and devices for production needs. Graduation and calibration of complex types of electrical devices and installations. Determination of malfunctions of operating devices and installations. Setting up and fine-tuning power supply systems together with ballasts and control equipment. Determination of the degree of suitability of complex electrical equipment.

Must know: basic methods for fault detection of complex electrical equipment and systems automatic regulation; design, principle of operation, rules of regulation and operation of test installations, electrical power sources, electrical devices and electrical measuring instruments; basic requirements for certified products; fundamentals of electronics, theory of automatic control, computer technology and programming; rules for reading electronic circuits of any complexity.

Average required professional education.

Work examples

1. Temperature control units - repair, assembly, testing, debugging.

2. Integrated engine regulator - assembly, testing.

3. Automation boxes and units such as AVZ, ARU, KZU - assembly, testing, regulation.

4. Voltage correctors such as TsKN and DKN - testing, regulation.

5. Magnetic heads and disk-code systems - repair, regulation.

6. Electrical converters - repair, inspection, testing.

7. Dangerous temperature alarms - repair, regulation, testing.

8. RIO type signaling devices - regulation, testing.

9. Anti-icing systems, trimmer controls - defect detection, repair, testing, regulation.

10. Thermostatic devices type TR, RD, TRV - repair, regulation.

11. Cabinets of stabilized electrical power supply of the VP-M system - testing.

§ 240. Electrician for testing and repair of electrical equipment (8th category)

Characteristics of the work. Complex adjustment, regulation and commissioning of complex and experimental aircraft electrical equipment systems with the implementation of restoration and repair work. Diagnosis, testing and analysis of failures in the operation of electronic systems, automatic devices, panels, consoles, complex electrical units, software mechanisms. Systematization of failures in the operation of electrical equipment and development of recommendations for their elimination and prevention. Carrying out tests using precision measuring instruments, service installations, their adjustment and regulation. Defects and rejection of electrical units in accordance with technical specifications. Drawing up schematic diagrams and sketches with performing the necessary calculations for the manufacture of installations for regulating and testing individual electrical equipment systems.

Must know: the design of electrical equipment systems being repaired; technology for repair, assembly, regulation and testing of complex electrical systems; methods for detecting and eliminating the most complex faults found in electrical equipment; the procedure for organizing a set of works on adjustment, regulation and troubleshooting in aircraft electrical equipment systems; requirements for certified products; the design of the instruments used to measure the parameters of electrical equipment and methods for checking them; fundamentals of the theory of automatic control, computer technology.

Secondary vocational education required.

Work examples

1. Automatic panels of the APD type - repair, adjustment, testing.

2. Aerial cameras such as AFA, NAFA - testing and regulation.

3. Vacuum pumps type VN - testing, regulation.

Electromechanic for elevators, 1st category

Characteristics of work.

1. Filing of surfaces, deburring of parts.
2. Correction of threads using dies and taps.
3. Marking simple parts using a template.
4. Cutting steel ropes manually.
5. Washing and lubricating parts.
6. Replacement of lighting lamps.
7. External inspection of the mechanisms, components and electrical equipment of the elevator.
8. Checking the presence and serviceability of lighting in the shaft, cabin and machine room, as well as the condition of the shaft and cabin fencing.
9. Evacuation of passengers from the elevator car in case of a sudden stop.
10. Carrying out work on dismantling, repairing and installing elevator equipment under the guidance of an electrician for elevators of a higher qualification.

Must know:

Techniques for metalworking parts;
- purpose and conditions of use of metalwork tools and linear measuring tools;
- main thread dimensions of fasteners;
- name and purpose of lubricants;
- basic information about the structure and purpose of the elevator and its components;
- purpose of electrical devices;
- brands and cross-sections of wires used in elevators.

Work examples.

1. Bolts, screws, nuts - threading with dies and taps.
2. Parts made of sheet and angle steel - filing the surface and removing burrs.
3. Round and angular strip steel - cutting with a hacksaw according to the finished markings.
4. Components and parts of mechanisms and electrical devices - cleaning, washing and lubrication after disassembly.

Electromechanic for elevators, 2nd category

Characteristics of work.

1. Metalworking of parts according to 11 - 14 qualifications.
2. Unwinding the rope from the coil and measuring the required length.
3. Preparation of pipes for electrical wiring according to the finished markings.
4. Refilling the tool.
5. Marking and cutting out gaskets according to drawings and sketches.
6. Disassembly and assembly of mechanical and automatic locks, gates, limit switches, floor switches, calling devices.
7. Identification and elimination of faults in lighting, alarm and elevator drive control circuits in relay-contactor elevator control systems.
8. Carrying out work on dismantling, repairing and installing elevator equipment under the guidance of an electrician for elevators of a higher qualification.

Must know:

Techniques and sequence of operations for machining parts;
- the procedure for disassembling and assembling elevator components and mechanisms;
- general information about tolerances and fits and the procedure for indicating them on the drawings;
- device lifting mechanisms(winches), blocks, pulleys, drums;
- basic information about the design and purpose of typical elevators;
- electrical circuits lighting circuits, alarms and elevator drive control systems;
- basics of electrical engineering;
- arrangement of AC electric motors;
- rules technical operation electrical installations of consumers;
- interindustry rules on labor protection (safety rules) during the operation of electrical installations as they relate to the operation of elevators.

Work examples.

1. Bolts, nuts, screws - thread cutting with taps and dies.
2. Parts made of strip and angle steel - marking, punching and drilling holes with portable power tools.
3. Niches, grooves, holes in partitions and walls - punching according to the finished markings and sealing.
4. Lamps, sockets, switches, sockets and calling devices - repair and installation after removing the voltage in the relevant circuits.

Electromechanic for elevators, 3rd category

Characteristics of work.

2. Checking and adjusting the mechanical and electrical equipment of elevators in single control mode.
3. Determination and elimination of faults in lighting, alarm and elevator drive control circuits.
4. Mechanical processing of parts according to 7 - 11 qualifications.
5. Installation, alignment, connection of electric motors.
6. Cutting and soldering cables and wires with various solders, laying them in pipes or bundles in the shaft and in the machine room.
7. Replacement of steel ropes with their fastening to the suspension units of the cabin and counterweight.
8. Riveting parts.

Must know:

Technical requirements for the dismantling, repair and installation of elevator equipment;
- circuit diagrams control elevators in single mode;
- methods of connecting, terminating and connecting wires and cable cores;
- sequence of disassembly and assembly of mechanical components and electrical devices;
- device asynchronous motors, transformers, relays and magnetic starters, sudden braking arresters;
- rules for using electrical measuring instruments and means of linear-angular measurements;
- basics of electrical engineering;
- device rules and safe operation elevators;
- rules for the design of electrical installations in terms of the requirements for electrical equipment of elevators.

Work examples.

1. Electrical measuring instruments - determination of parameters of electrical circuits.
2. Control stations with relay contactor equipment - regulation of electrical devices, cleaning of contacts.
3. Transformers - installation and connection.
4. Electric motors - disassembly, cleaning, repair, lubrication, assembly.

Electromechanic for elevators, 4th category

Characteristics of work.

1. Carrying out work on dismantling, repairing and installing elevator equipment.
2. Inspection, adjustment and testing of elevator equipment in a group of up to two elevators.
3. Disassembly and assembly of the winch.
4. Replacing the worm pair in the gearbox.
5. Production of installation and marking templates.
6. Checking the insulation condition with a megger and measuring the value of its resistance in electric motors, transformers, cable networks and control system circuits.
7. Preparing the elevator for technical inspection.
8. Maintaining the necessary technical documentation.

Must know:

Technology for disassembling and assembling elevator equipment components;
- schematic electrical diagrams of serviced elevators;
- arrangement of semiconductor circuit elements;
- methods for dismantling, installing and replacing electrical wiring of lighting, alarm and control circuits, technical requirements, presented to them;
- brands and cross-sections of wires, rules for assembling wires, fuse-links and protection devices depending on the current load;
- basics of radio engineering;
- the principle of operation of two-way loudspeaker communication for dispatch control of elevators.

Work examples.

1. Semiconductor rectifiers - assembly, replacement and connection to the circuit.
2. Winches various types- disassembly, assembly, adjustment, replacement of seals and bearings.
3. Elevator shaft equipment - checking and adjusting regulated dimensions and clearances.
4. Electrical wiring of lighting, alarm and control circuits - production of wiring harnesses and their replacement in the shaft, machine and block rooms.

Electromechanic for elevators, 5th category

Characteristics of work.

1. Carrying out work on dismantling, repairing and installing elevator equipment in a group of up to three elevators.
2. Inspection, regulation and testing of elevators with a control system for a group of up to three elevators.
3. Identification and troubleshooting of elevators with a control system for a group of elevators up to three, including the use printed wiring electrical control circuits with electronic microelements.
4. Periodic and partial technical inspection of elevators.

Must know:

Technical requirements for testing elevators;
- requirements for the quality of repair, installation and testing of mechanical and electrical equipment of elevators;
- service life of parts and assemblies and methods of taking measures to increase them;
- regulations on the system of scheduled preventive maintenance;
- structural design of elevator equipment;
- schematic, electrical diagrams for controlling a group of elevators up to three; basics of radio-electronic technology.

Work examples.

1. A unit with a control system for a group of elevators up to three - identifying and eliminating faults, adjusting the control system.
2. Elevators with automatic drive of shaft and cabin doors - repair, replacement and regulation.
3. Low-voltage complete device - disassembly, adjustment and replacement of component elements, assembly.
4. Printed circuit boards, individual electronic elements - replacement.

Electromechanic for elevators, 6th category

Characteristics of work.

1. Carrying out work on dismantling, repairing and installing elevator equipment in a group of elevators up to six and high-speed elevators.
2. Inspection, regulation and testing of elevator equipment with a control system for a group of up to six elevators.
3. Identification and elimination of faults in mechanical components, lighting, alarm and control systems in a group of elevators up to six and high-speed elevators.
4. Characterization of electronic boards.

Must know:

Technical requirements for the installation and repair of high-speed elevators;
- basics of radio electronics;
- schematic electrical diagrams for controlling a group of elevators up to six;
- arrangement of oil buffers;
- diagrams of internal connections of windings of DC electrical machines, generators, thyristor regulators used in high-speed elevators;
- rules for using the control and measuring instruments used;
- methodology for testing elevators in group mode.

Work examples.

1. Oil buffers - installation and testing.
2. Combined catchers - disassembly, assembly, adjustment.
3. Lighting, alarm systems, elevator control systems in a group of up to six - troubleshooting and troubleshooting.
4. Telescopic door drives - dismantling, installation, adjustment.

Electromechanic for elevators, 7th category

Characteristics of work.

1. Carrying out repair, maintenance and testing of elevator equipment.
2. Checking, regulation and adjustment of elevator control systems using microelectronic and microprocessor technology.
3. Diagnostics of electronic components and boards accurate to the electronic element.
4. Disassembly of devices, components of elevator equipment and their repair with replacement of parts and electronic elements.
5. Inspection, repair, regulation and adjustment of electric drives of elevators.
6. Preparation of frequency-frequency equipment adjustable electric drives elevators to testing.
7. Setting up programs in electronic devices ah control of elevators during testing and in operating modes.

Must know:

Design, electrical and other features of electronic devices based on microprocessors;
- a system for programming microprocessors in elevator control devices and frequency converters electrical devices of the main drive and elevator door drive;
- methods of diagnostics and repair of microprocessor devices and elevator equipment;
- design, purpose and possibilities of using instrumentation and diagnostic equipment when checking and adjusting electronic equipment of elevator control systems;
- technical requirements for the repair of electronic devices of elevator control systems based on microprocessor technology;
- fundamentals and principles of constructing distributed microprocessor control systems for elevators.

A secondary vocational education is required, at least one year of work experience as an electrician in elevators of the 6th category, or at least two years of work experience in other occupations of workers in the maintenance of microprocessor equipment.

Work examples.

1. Low-voltage complete device using microelectronics and microprocessor technology - troubleshooting and troubleshooting.
2. Complex control and measuring equipment - repair and adjustment.
3. Variable-frequency electric drive - preparation for testing, introduction and configuration of programs.
4. Electronic components and boards - diagnostics accurate to the electronic element of the equipment, repair with replacement of parts and electronic elements.

Electromechanic for elevators, 8th category

Characteristics of work.

1. Carrying out work on the modernization of elevator equipment, including equipment with program control based on microprocessor technology, programmable control devices for electric drives of elevators.
2. Comprehensive Maintenance, inspection, repair, adjustment and testing of local controllers of a distributed elevator control system.
3. Diagnostics of microprocessor equipment, electronic control equipment, local controllers and data transmission equipment based on microprocessor circuits of a high degree of complexity.
4. Repair and parametric adjustment of frequency-controlled electric drives of the elevator winch and door drive.
5. Complex regulation of electronic devices of microprocessor control systems for elevators.

Must know:

Algorithms for the functioning of electronic equipment and microprocessor systems for electric drives and elevator automation;
- design features elevator control systems and data transmission systems about faults in local networks of the elevator control system and global networks of the elevator operation monitoring system;
- methods and methods for re-adjusting electronic equipment of electric drive systems and elevator automation.

A secondary vocational education is required, at least 2 years of work experience as an electromechanic in elevators of the 7th category, or at least three years of work experience in other occupations of workers in the maintenance of microprocessor equipment.

Work examples.

1. Special, modernized elevators - identification and elimination of faults with replacement of the element base.
2. Local controllers - maintenance, inspection, repair, adjustment.
3. Microprocessor systems - complex regulation of electronic devices of elevators with a control system for a group of elevators.
4. Variable-frequency drives - setting up program parameters for winch electric drives and elevator door drives, performing adjustment work.

Professional standard for the profession Electrical mechanic for elevators -.

Unified Tariff and Qualification Directory of Works and Professions of Workers (UTKS)
Part No. 2 of Issue No. 2 of ETKS
The issue was approved by Resolution of the Ministry of Labor of the Russian Federation dated November 15, 1999 N 45
(as amended by Order of the Ministry of Health and Social Development of the Russian Federation dated November 13, 2008 N 645)

Electrician for automation and instruments technological equipment

§ 181. Electrician for automation and technological equipment devices of the 3rd category

Characteristics of work. Repair, technological maintenance, assembly, inspection, testing, installation, adjustment and delivery with the removal of diagrams of individual units, blocks and mechanisms of electromechanical, electronic and electrical elements of instrumentation equipment, automation and electrical automation equipment, computer systems, adjustable electric drives and devices with program control as part of technological equipment.

Must know: arrangement of individual units, blocks and mechanisms; purpose, conditions of use and basic information about the operation of the equipment being serviced; methods of safe maintenance and repair of equipment; kinematic transmissions and technical drives; fundamentals of electrical and radio engineering.

§ 182. Electrician for automation and technological equipment devices of the 4th category

Characteristics of work. Repair, maintenance, assembly, inspection, testing, installation, adjustment and commissioning of electronic, electrical and electromechanical elements of instrumentation equipment, automation and electrical automation equipment, computer systems, machine tools and other equipment with program control devices with replacement or fine-tuning and adjustment of replaceable units, blocks and mechanisms as part of technological equipment. Diagnosis of malfunctions of electronic units and assemblies accurate to a replaceable unit or a typical replacement element using software or autonomous devices. Repair and regulation of electronic, electrical and electromechanical blocks and assemblies, analog-digital devices, adjustable electric drives, program control devices. Entering programs manually and monitoring their execution on program control systems.

Must know: design and electrical features of electronic devices and units; design and purpose of electronic devices, algorithm of their functioning and relationship with other devices; diagnostic methods and methods for testing electronic components and components; methods and procedures for equipment maintenance; methods of repair and restoration of replaceable electronic components and blocks; technical requirements for the performance of electronic devices; basics of programming, precision mechanics, automation, computer technology.

§ 183. Electrician for automation and technological equipment, 5th category

Characteristics of work. Repair, maintenance, full autonomous and comprehensive testing, testing, installation, adjustment and commissioning of electronic, electrical and electromechanical elements of equipment, instrumentation and installations, computer equipment, automation equipment, machine tools and equipment with program control in accordance with requirements technical specifications and using test software. Repair, adjustment and testing of electronic devices and products designed on the basis of microelectronic and integrated circuits. Troubleshooting accurate to the functional standard replacement element (TEE). Repair of boards of electronic control devices, program control, computer equipment, analog-digital devices. Diagnosis of faults in program control systems. Carrying out work on serial samples of new equipment. Elimination of the flow of failures of computer systems, automation equipment, instrumentation and installations, machine tools and equipment with program control and replacement of failed replacement units, regulation and partial disassembly of equipment.

Must know: design features of the equipment being serviced; schematic and functional diagrams of program control systems; methods of disassembly, assembly, repair, installation, regulation and testing of serviced equipment, components and units; used equipment, technological equipment and firmware; purpose, principle of operation and interaction of individual devices and products as part of subsystems and complexes; methods of working with bench equipment when repairing thermal power plants and power supplies; the principle of setting the operating modes of individual devices, blocks, devices and components and putting them into operation using special program control systems; command system for devices and blocks; composition, types and methods of operation of the used samples of control and measuring equipment and test benches; fundamentals of microelectrical engineering.

§ 184. Electrician for automation and technological equipment devices of the 6th category

Characteristics of work. Repair, maintenance, full autonomous and comprehensive testing, testing, installation, adjustment and commissioning of electronic, electrical and electromechanical complexes of devices and products, instrumentation, installations and equipment, computer systems, automation equipment, multi-operational machines and other equipment with program control in accordance with the requirements of technical specifications and using test software. Repair of technological equipment with replaceable units and units based on microprocessor integrated series of elements. Diagnosis of electronic microprocessor equipment using software and firmware packages. Repair, regulation and maintenance of the electronic part of proportional and disproportionate electric drives. Restoration of components, blocks and mechanisms of serviced equipment.

Must know: design, purpose, operating conditions of electronic microprocessor equipment; methods and methods of electrical, electronic autonomous and complex adjustment of electronic microprocessor equipment; architecture and operating algorithms of the used microprocessor series of electronic integrated circuits, command systems, methods and methods for programming devices and units, technical requirements for the repair of electronic devices of microprocessor-based equipment, electrical automation, machine tools and program-controlled equipment; analogues of imported integrated circuits and other components.

Secondary vocational education required.

§ 185. Electrician for automation and technological equipment, 7th category

Characteristics of work. Repair, maintenance, inspection, testing, installation, adjustment and commissioning of electronic devices based on microprocessors, mini- and micro-computers, control modules of multi-operational machine tools with program control, robotic technical complexes (RTC), flexible production systems (GPS) , personal computers and terminal devices of the teleprocessing system. Diagnosis of electronic components and modules with an accuracy down to the electronic element as part of the equipment. Disassembly of devices and repair of components with replacement of failed electronic elements. Adjustment, adjustment and testing of electronic control devices in stand-alone and operating modes. Repair and regulation of electric drives controlled by mini- and micro-computers. Preparation, introduction and debugging of programs in electronic control devices. Microprocessor programming.

Must know: design, electrical and other features of electronic devices based on microprocessors or operating under the control of mini- and micro-computers and microprocessors; methods for diagnosing and repairing microprocessor devices and products; device, purpose and possibilities of using control, measuring and diagnostic equipment based on microprocessor technology; technical requirements for the repair of electronic devices of equipment based on microprocessors, mini- and micro-computers; fundamentals of circuit design, microprocessor technology, robotics; principle of GPS construction.

Secondary vocational education required.

§ 186. Electrician for automation and technological equipment, 8th category

Characteristics of work. Participation in the development and construction of prototypes of electronic equipment, in the modernization of equipment with program control based on microprocessor series of integrated circuits, program control devices and electrical automation, aimed at increasing the reliability of equipment operation. Comprehensive maintenance, adjustment, repair, inspection, testing, installation and commissioning of data transmission equipment based on matrix circuits and other complex electronic equipment. Diagnosis of microprocessor equipment, electronic control equipment and data transmission equipment based on microprocessor circuits of a high degree of integration. Repair and parametric adjustment of electric drives, control systems, computer systems. Comprehensive regulation of electronic devices RTK and GPS.

Must know: architecture, operating algorithm and system of machine commands of custom circuits of large and medium degree of integration, design and architectural features control systems and data transmission systems in local and global networks; methods for diagnosing and troubleshooting RTK, GPS and data transmission systems operating in real mode using various controllers; methods and methods for reconfiguring electronic equipment of control systems and data transmission equipment.

Secondary vocational education required.

Section ``Production and repair of aircraft, engines and their equipment``((ETKS No. 22))

§ 236. Electrician (4th category)

for testing and repair of electrical equipment

4th category

Characteristics of the work. Disassembly, repair, assembly and regulation of medium complexity electrical units. Definition technical condition elements included in the electrical mechanism. Troubleshooting electrical mechanisms that require plumbing work. Repair of electrical harnesses of medium complexity with sealing of tips and soldering of plug connectors. Determining the condition of electrical wires using electrical measuring instruments. Testing of simple electrical equipment using special stands and installations. Preparation of repair cards.

Must know: the design of aircraft being repaired; design, purpose, principle of operation, installation and fastening locations of the devices, electrical mechanisms and equipment used; technology for repair and regulation of electrical equipment; rules for checking the insulation resistance of electrical wires; basic information about the brands, purpose and properties of materials used in electrical equipment, as well as during its repair; basic information about the system of tolerances and fits, surface treatment parameters; electrical and kinematic diagrams of electrical units being repaired; methods for testing electrical units and their parts on test benches; design of electrical measuring instruments used and rules for their use; basic laws of electrical engineering, electronics; technical and working documentation; plumbing in the scope of work performed.

Work examples

1. Automatic machines such as AVP, AV, AVD, AMO - disassembly, repair, assembly.

2. Type A ammeters, AF repair, regulation.

3. Blocks of the BPS-repair type.

4. Voltmeters type VP, EV, VF, VA, LUN-repair, regulation.

5. Brake release sensors - disassembly, repair, assembly.

6. ZM type locks - repair, regulation, assembly.

7. Ignition coils type SK, KNA, KMB, KR-repair with installation in units.

8. Pneumatic switches of the UP type - repair, regulation.

9. Electric hydraulic cranes type GA-repair, regulation.

10. Electric heaters, heaters - repair, assembly, regulation.