Every modern family has inflatable mattress. It serves as a bed for unexpectedly arriving guests; it can be taken on vacation: it is useful for swimming, can be used as a bed, and is comfortable for sunbathing.

But sometimes on vacation the problem of air deflation arises, let's see how to solve it,how to seal an air mattress.

In contact with

Product Features

An air mattress is a cavity made of a special material of various sizes, which, when filled with air, is converted into a sleeping place. They come in single and one-and-a-half sizes, but there are also wider air beds. They also differ in height - there are large models up to 50 cm, and small ones up to 23 cm.

They have become firmly established among students, nomadic groups, and those who do not have permanent housing and are forced to move frequently. It is also good to have an air bed if the area of ​​​​the apartment is small, so that you can put it away in the closet in the morning.

The presented products are made of polyvinyl chloride - this is a fairly soft elastic material, but, unfortunately, prone to easy damage.

Therefore, every home should know how to implementair mattress repair.

For those who cannot stand the chemical smell, environmentally friendly ones are available.mattresses without glue and odor.

They are often purchased for children or elderly people who react painfully to various chemical components.

Attention!A high mattress can be used as a permanent sleeping place by covering it with a blanket. In this form it looks like a regular bed.

Such products are indispensable on vacation; you can sleep on them, sunbathe and swim.

Valve Troubleshooting

If there is no damage to the product in the form of holes or cuts, and it gradually releases air, then the reason lies in a malfunction of the valve. Ifair mattress repair shopis far away, you can fix the problem yourself at home, following the step-by-step instructions:

1. Fill the product with air and lubricate the valve with soap foam. If it allows air to pass through, foam will appear around it.
2. Then you need to remove the adjacent valve, and then the rubber gasket.
3. The end of the valve must be sanded with fine sandpaper and lubricated with silicone grease.
4. Then place the valve in its original place and inflate the product again to check.

Serious valve damage can only be repaired in a workshop. With such a simple task,how to fix an air mattress, any owner can handle it.

How to detect a puncture

Preliminary repair requires studying the issue,how to find a hole in an inflatable question, because it is this unfortunate nuisance that becomes the cause of spoiled rest and sleep. There are several methods for searching:

1. Tactile. This puncture detection method does not have any materials at hand. The mattress must be well inflated and your hands should be held above its surface at a height of 2-3 cm. At the location of the hole, your hands will feel a trickle of air. To increase sensitivity, hands should be moistened with plain water.The puncture site can also be detected by ear - hissing and whistling will be heard from the damage.
2. Soapy. Dilute a strong soap solution and then apply it to the surface with a sponge. Bubbles will form at the location of the puncture; mark it with a marker.
3. Submersible. Mattresses small size you can simply immerse it in a container of water and see where air bubbles emerge from.
4. Water. In this method, water is poured into the mattress - a small amount is used. The mattress needs to be shaken and then inspected. If a wet spot is found on its surface, then this is where the puncture is located.

Advice!You need to start looking for damage from the valve, and then from the side seams: they are the ones that suffer most from overload. Next, you need to check the lower part, which is in contact with the ground or floor, because it is more susceptible to punctures.

Preparation for repair

Before starting repairs, it is necessary to prepare its surface for work. First, the mattress must be deflated and thoroughly dried.

You need to know how to deflate mattresses correctly. In simple models, it is enough to open the valve and wait a certain time. You cannot press or crush it.

Other models do this differently.

For example, it is necessary to know exactlyhow to deflate a BESTWAY mattress, because it has a special damper installed that prevents the mattress from deflating if the valve cover is accidentally opened.

In this case, you need to open the lid and move the plate to the side, then the air will escape.

Now the puncture sites must be degreased with alcohol, acetone or gasoline. The flock coating will have to be removed, that is, carefully cut off. Rubber or plastic does not require additional processing or cleaning.

Preparing the patch

In making a patch you should knowhow to seal an air mattress. If there is no material suitable for repair at hand, then any piece of thin rubber will do. You can take a piece from a car or bicycle tube, a children's toy, or any rubberized object. You can also make a patch from cotton fabric pre-impregnated with rubber glue.

What glue is suitable for repairs?

For product repair, it is importantwhat glue to use to seal an air mattress. There are many adhesives, each designed for working with a specific type of material.

Experts advise choosing universal varieties, rubber and PVC composition.Once dry, the glue should form a strong, elastic and waterproof connecting layer.

Glue should be used in minimal quantities so that the layer is thin - excess will not help glue the rubber parts. For repairs, it is recommended to use the following types of glue:

1. Moment. This is a universal adhesive; it bonds almost any material: rubber, plastic, PVC, fabric and much more.
2. Polyurethane shoe material. This is a reliable adhesive; it forms a strong layer between the gluing surfaces. Only when applying glue should the surfaces be connected and dried with a hair dryer.
3. Glue for PVC. Air mattresses are often made from polyvinyl chloride, so this type of glue is best suited for them. It is necessary to glue by applying 2 layers to both surfaces, after which the composition is left to stand for 20 minutes.
4. Super moment. Fast-acting adhesives are also suitable for repairing this product, but contain substances that damage the surface.Its main disadvantage is premature hardening and fragility during product operation.When the mattress dries, cracking of the adhesive mass may be detected on the folds, which will again lead to the need to make repairs.
5. Real rubber glue. When gluing, it does not leave stains. It is necessary to apply two layers of glue to the surface, let it dry, then connect the surfaces and place a load on them for a day.

Advice!If you don’t have a wide choice at hand, you can patch with any glue. It is important to follow the instructions for gluing surfaces.

What is needed for repair

Now we should talk abouthow to seal an air mattress at home, what tools and tools will be required for this? If there is no special repair kit, then any available materials will do:

• universal glue “Moment”;
• flaps of thin rubber;
• alcohol or acetone;
• fabric gloves;
• glue brush;
• marker;
• soap or shampoo;
• water;
• fine sandpaper.

The listed materials are almost always available in the house, so it is not necessary to purchase a special repair kit, because it is quite expensive.

How to seal a puncture

Having found and identified all the defects, you can begin repairs yourself. We offer step-by-step instructions,how to glue an air mattress:

1. Remove the air from the mattress, straighten it and carefully lay out the area to be repaired on a level place.
2. Use sandpaper to carefully clean the bonding areas on the mattress and on the patch.
3. Cleaned areas must be degreased with any available means.
4. Apply a thin layer of glue to the prepared surface of the product and patch with a brush and let it dry for 10-15 minutes.
5. Place the patch on the damaged part and let the glue dry overnight.

Important:You can place a small weight on the patch. A day later, the repaired mattress is inflated with air, and the tightness is checked by lubricating the repair area with soap foam.

There remains one more significant point,how to seal an air mattress on the velor side, because in this situation the above repair technology will not work. This applies to mattresses from the popular brand Itex and other manufacturers. To apply a patch to such a product, you need to do this:

• Clean the velor surface to the size of the patch. To do this, moisten the surface with acetone and clean off the lint with a blunt knife;
• Wipe the smooth surface again with acetone, and then you can apply glue;
• Allow the glue to dry and apply the prepared patch to the surface in the same way. Press it onto the surface of the mattress and let it dry overnight.

Advice!How and how to seal an Intex air mattress? The patch can be applied from the inside. In this case, the damaged area is pushed out through the valve and sealed in the usual way. The inside surface is rubber and does not require additional processing.

Repairing large holes and cuts

How to seal a hole in an air mattress, if it is more than 5 mm. In this situation, repairing it yourself may be impossible; it is better to entrust it to specialists. In specialized workshops, repairs to the inside of the product and sealing of large cuts and holes are carried out using special equipment.

Seam damage repair

Complex issuehow to seal an air mattress along the seam,Experts will help you decide.

Home repairs may not work out, so if there is a workshop nearby, it is better to take the mattress to a specialist. Damage along the seam is repaired from the inside of the mattress.

To do this, the torn section of the seam is squeezed out through the valve, and then you can begin repairs, following the instructions:

1. Wipe the rubber surface with alcohol to degrease.
2. Leave for complete drying - during this time, cut out a suitable patch, which is also wiped with alcohol.
3. Lubricate the sides to be joined with glue and attach them to each other.
4. Press them tightly and leave to dry for 12 hours.

Once the glue dries, turn the mattress out and inflate with air.This is necessary to check the quality of self-repair.

Damage Prevention

To ensure that the mattress is no longer damaged, it is recommended to follow the following operating rules:

• Before throwing the mattress on the ground, remove all sharp objects or place a thick cloth underneath it.
• Do not inflate the product too much.
• Protect the product from the claws of pets.
• You should not drag an inflated mattress along the ground, especially when a person is on it.
• It is prohibited to jump or sit suddenly on the mattress.
• The air must be released slowly.
• Wash with soapy water.
• Before folding the mattress and placing it in the closet, it must be thoroughly dried.

As can be seen from the above,how to seal an air bed– the process is quite simple, you can easily handle the repair of the product yourself. Even better is to prevent such damage. But if a puncture occurs, do not despair - everything is in your hands.

It doesn't take any special skills to seal an air mattress and extend its life. It is worth mentioning that not all products make sense to repair. You can figure out whether a product cannot be disposed of if damaged, even at the time of purchase. Air mattresses worth trying to seal come with a patch and rubber glue. If there is no repair kit, it is most likely easier to throw away the product.

Features of repairing bathing mattresses

Mattresses for relaxing on the shore and water are more often damaged than sleeping mattresses when they come across a sharp stone, a random splinter - any sharp object. At the same time, a repair kit is rarely included with them - this means that the mattress cannot be repaired. You should pay attention to its design.

Products consisting of two or more independent sections can be glued together. A puncture in a separate part causes inconvenience, but has virtually no effect on safety when swimming. It can and should be repaired. It is better to avoid swimming on a sealed single-section mattress.

These recommendations apply to a single injury. If a multi-section mattress is damaged a second time, and in another section, use on water is not recommended. The same thing happens if there are punctures in one section, but from different sides (bottom and top), since in water the mattress endures strong loads - air pressure from the inside, water pressure from below and from the sides, and body pressure from above.

For repairs you will need:

• a piece of material similar in quality to a mattress;
• waterproof glue;
• degreaser, solvent, acetone, alcohol or high octane gasoline;
• a heavy object with a flat surface - a press.

Important! The gluing area will always be a risk area. Do not swim far on a repaired mattress and do not load it beyond the limit specified by the manufacturer in the instructions.

How to determine the puncture site: two ways

Repair of air mattresses (of any type) begins with determining the location of the damage. No cuts or rips along the seam can be found special labor, it is more difficult to see a pinhole puncture. For cyclists and owners inflatable boats this problem is well known.

Method with water:

1. The balloon filled with air is lowered into the water and submerged.
2. Air begins to escape from the damaged area, bubbles rising in a stream - this is an indicator of the puncture site.
3. In order not to lose the detected defect, it is first pinched with a finger and then outlined with chalk, soap or a contrasting alcohol marker.

The disadvantage of this method is that you have to wet the product and then dry it thoroughly for further gluing. This is especially inconvenient when repairing velor mattresses - the silky surface takes a long time to dry.

Testing without water

If there is no container to put the mattress in or there is no time to wait for it to dry, then the puncture is found by sound. The product is arbitrarily squeezed and listened to. Coming out of a small hole, the air hisses.

You need to be careful not to make mistakes. It is more convenient if the mattress is not inflated tightly - then the dense part is moved around the perimeter in order to more accurately determine where the quiet hiss is coming from. The method is better suited than others for coated products, but is the least accurate.

Another method is using soap. The product will have to be moistened, but not as much as when lowered into water. The point is to inflate the mattress and lather the approximate puncture site. There is no need to press: if there is damage, the air will come out of it, inflating the bubble. It is from this that the future area for the patch is identified.

Advice! If you have absolutely nothing to circle the puncture with, insert a match or a toothpick with a cut tip into it.

Several ways to repair air mattresses

To firmly glue an air mattress, be sure to follow five steps:

1. Cleaning up.
2. Degreasing.
3. Drying.
4. Primary treatment with adhesive composition.
5. Bonding with placement under the load within 24 hours.

Important! The patch material must be identical to the mattress or as close as possible in quality and composition.

Ideally, a double patch is installed - with the inner and outside, especially if we are talking about a cut or a strong tear. For a small puncture, external sealing is sufficient. In any case, it is necessary to ensure that the glue does not leak into the mattress - otherwise it will stick together and become at best uncomfortable, and at worst unusable. Therefore, the glue is applied in a thin, uniform layer, not reaching the edge of the patch 1-2 mm.

Stripping is the complete removal of everything that will interfere with the adhesion of the glue and the base. Smooth products are washed thoroughly, but velor types Intex, you will have to free it from lint. To do this, use fine-grain sandpaper; you can use a knife, razor, etc. with caution.

Urgent repair of minor damage using improvised means

Mounting tape is used as an “ambulance” for a damaged watercraft. Its advantage over other products of similar purpose lies in its tight fit and elasticity. The method is also convenient in that it can be used both at home and on the go, without the need to wait until the first layer of glue dries. The disadvantage of this method is less strength and durability and the inability to repair a strong tear. Scotch tape is good against pinholes and small cuts.

Interesting fact
Gray tape with a stretching effect is used by plumbers to temporarily fix leaks. And insulation made from such material lasts for years.

Mode of application:

1. Clean and degrease the damaged area.
2. Let dry.
3. Seal with tape. A long cut is preferably made in two layers: the first along, the second across.

About the same specifications has white insulating tape for electrical wires. It is inferior to “rubber” tape in terms of width and stickiness. It is suitable for temporary repair of a pinhole puncture in a sleeping mattress - but it must be secured with two cross-sections.

Repairing major damage

It is not practical to repair a mattress that is torn at the seams using adhesive tapes: the pressure on the side elements is too great. In this case, it is necessary to install a patch.

Advice! The encircling rigid frame reduces the deformation of the mattress, making it more comfortable to sleep on. And this same element is a guarantee that after serious repairs the product will still serve.

Possible difficulties:

1. A model in which the side elements are not an addition, but part of the inflatable balloon, is inconvenient for repair at home.
2. Reliable and tight coupling ensures uniform load pressure. To do this, it must be flat at the bottom, heavy and grip every millimeter of the patch. In case of significant damage, selecting the required cargo dimensions is difficult, but necessary. If such a pressing tool is not found, and improvised materials of different weights and shapes are used, then some areas will leak air after the first use of the mattress.

To repair a mattress along the seam you will need:

• two smooth thin slats;
• clamps;
• rubber-based adhesive;
• acetone;
• rectangular patch.

Procedure:

1. The area around the damage is treated with acetone.
2. After it evaporates, glue is applied in a thin, even layer.
3. The same preparatory work carried out with two patches.
4. Leave the lubricated parts in air (the time for this stage is individual for each type of glue, it is indicated on the tube).
5. Carefully insert the inner patch and align its middle with the center of the damage.
6. The second patch is applied on top and smoothed thoroughly. After connecting the parts, there should be no air bubbles left between them.
7. From below and above the glued seam, on top of the patch, slats are applied and secured with clamps.
8. Leave the mattress in a vice for a day or half a day.

More in a reliable way repair is the only vulcanization used to repair automobile tires. It is better to contact your nearest tire shop for this service.

Air mattresses are convenient for relaxing on the water or as guest beds. If the product is damaged and begins to leak air, you should try to seal it. The procedure does not require any special skills, just accuracy and time. A repaired single-section mattress will only last on the shore; if there are several sections, it is quite acceptable to swim on it.

Air mattresses are in high demand, and this is not surprising. They are convenient for picnics and outdoor trips, for good rest V country house, and they can also be used as furniture in the apartment.

Air mattresses are simple and unpretentious, taking up little space, especially when deflated. Unfortunately, they are quite easy to damage. Holes appear from long-term storage and improper use. But this does not mean that the mattress should be thrown away. You can resuscitate him without any serious effort on your own.

The Intex air mattress is an excellent alternative to standard, familiar furniture. But they require compliance with certain operating rules, otherwise the product will not last long. If you use an air mattress according to all the rules, it will perform its functions for quite a long time.

The mattress is inflated using pumps specially designed for this purpose. Many mattresses already have built-in air pumps. The product cannot be inflated with a car compressor.

There is no need to pump it with air; you need to constantly monitor the process. The mattress should be fairly elastic, but not too hard. Over-pumping will reduce service life. If you take the mattress to the beach or outdoors in hot weather, it is better to inflate it directly there.

The deflated mattress is stored clean and dry. The product needs to be washed warm water with the addition of soap, do not use various abrasives.

To keep the air mattress intact, do not jump on it. You should also pay attention that there are no piercing or cutting objects near the mattress that could damage the product. You need to be careful if you have pets, because they can chew or scratch the mattress.

How and how to seal an air mattress

A damaged mattress can be repaired at home using simple and available funds. Mattress manufacturers Intex include a kit for home repairs. This is very pleasing; you don’t have to worry about where the repairs are being done, how much it will cost, and whether it makes sense. The kit includes glue, patches and film.

You can revive the product not only at home, but also in nature, in the country. It’s not entirely pleasant to go on a picnic and lose sleeping place due to a puncture. If air passes through the seam, you can temporarily treat the seam with superglue and repair the mattress in a more comfortable environment.

How to seal an Intex mattress at home? When faced with a cut on such a product for the first time, there are no problems with what to seal it with - there is a kit carefully assembled by the manufacturer. However, if the trouble recurs after some time, there will simply be no materials left.

To prevent the patch from coming off, you need to thoroughly clean the damaged surface of dirt. It should be free of lint, dust, and animal hair. A regular nail polish remover or solvent is suitable as a cleaning agent.

After applying the product, wait a little, and then use something hard to remove lint and other dirt. When sealing an Intex mattress, you need to degrease with alcohol both the patch and the surface on which it will be applied.

Intex mattress repair at home

Further repairs depend on the nature of the damage. You can actually seal minor holes from cuts and punctures yourself. If the seam of the mattress is seriously damaged or the partition inside is torn off, it is better to turn to professional craftsmen, since such problems require special skills. Repair of Intex air mattresses is usually carried out in the same organization where the purchase was made.

To repair a mattress yourself, first find the place where it was damaged. It's not as easy as it might seem. If such a possibility exists, the product is inflated in absolute silence. The place where the hole appeared will emit a hissing sound, this is where the air escapes freely.

The popularity of inflatable furniture is explained by its ease of use and compact folded size. It can be used both on tourist trips and at home, as an extra bed. Active use of the product often leads to the appearance of holes through which air escapes, so owners often wonder how to seal an air mattress themselves.

Seal the mattress with glue (click to enlarge)

Violation of the integrity of a PVC product is not a reason to throw it away. Typically, sales centers for branded inflatable furniture provide repair services for their products. Specialists know how to properly restore a product. However, when choosing where to seal an air mattress, you must take into account that this is an expensive service.

Why is air coming out?

Intex products can deflate for various reasons. This is not always due to a puncture or rupture. The valve may be the source of the problem. It is possible that debris accumulated in the grooves does not allow the lid to be screwed on tightly enough; in this case, it is enough to rinse the part. A broken plug can be replaced.

Sharp objects or pets' claws may cause cuts in the fabric of the product. Seams come apart and tear due to improper use. internal partitions air mattress.

Defect detection methods

To repair the product, you need to find the location of the damage. Often the holes are small and almost impossible to notice. There are several methods by which you can detect a gap:

• The inflated product can be immersed in water. The hole will reveal itself as a stream of small air bubbles;
• at home, the rupture site can be found using a foamed soap solution, which is applied to the surface of the mattress. A large bubble will inflate over the rupture site;
• several liters of foam solution are poured into the inflated product. Turning the mattress over, you can find liquid flowing from the defects with a quiet whistle;
• It is recommended to sprinkle the surface of the air-filled mattress with flour or any powdery product. The air escaping from the hole will blow away the powder. Once a rupture is detected, the mattress is cleaned with a vacuum cleaner;

You can learn more from the video:

IMPORTANT! Usually, several damages appear at once. The area with a relief pattern that rips most quickly on air mattresses.

The detected defect should be marked with a felt-tip pen or marker.

We need to localize the place (click to enlarge)

Repair of inflatable product

Choosing how to seal an inflatable intex mattress, it is worth, if possible, using a branded repair kit, which is sold complete with the product. Manufacturers complete the set with velor patches, special glue and vinyl film. How to seal the mattress is described in detail in the instructions. It is included with the set.

If the set is lost or used, you can seal the mattress in other ways. The gluing process can only begin when the product is dry. It is important to choose the right glue to use for these purposes. It is better to use a rubber-based adhesive or another composition that retains its plasticity after drying. By gluing a patch with superglue, the owner risks irreversibly damaging his item.

Typically, the repair approach changes based on the location of the damage.

Elimination of punctures and cuts

The question of how to seal an air mattress is easily resolved. The patch can be cut from a rubberized item or use a patch from a tire repair kit.

On the smooth side of the product, it is enough to degrease the area around the hole with acetone or alcohol. The patch is processed using the same tool. For mattresses they are cut without corners. Glue is applied to both surfaces, which are pressed tightly against each other. The repair site is placed under a press for 12 hours.

If the mattress is damaged on the velor side, the lint from the surface around the hole should be cleaned off with fine-grained sandpaper. Next, the patch is glued in the manner described. Defects on the velor cannot be avoided with such repairs.

Watch the video to find out more:

You can seal the air mattress from the wrong side, then the puncture site on the surface will be almost invisible. To do this, the defect area must be pulled out through the hole to inflate the product. The patch is fixed with glue. After half a day, the product can be turned out and filled with air. When thinking about how to seal an air mattress, you need to take into account a number of advantages of the latter method: the tear site is effectively masked, the patch is held on the inside more securely, since the air that fills the bed presses on it. Although the repair process is more labor-intensive.

Failure to comply with the rules for operating the product leads to the fact that the consumer is often forced to look for an answer to the question of how to seal an air mattress at the seam. It is quite difficult to eliminate defective joints on your own. A patch placed on the seam from the wrong side will not last long. Manufacturers recommend contacting a service center for help.

ADVICE! Insulating tape can be used as a temporary fix for punctures. The sealed mattress can be used for several days.

Inflatable furniture is simple and easy to use. Thanks to such products, it is possible to provide full-fledged sleeping places for guests, and make outdoor recreation more comfortable. Careful use and adherence to operating techniques can save you from having to look for the answer to how to seal an air mattress at home.

Today, almost every home has air mattresses. You simply cannot do without them if guests arrive and you need to organize sleeping places for them. This attribute is also very convenient to take with you to the sea. You can sleep on it, sunbathe, and swim. As a rule, such mattresses are made of polyvinyl chloride - a soft elastic sheet material. Its disadvantage is that it is easily pierced. If you encounter such a problem, do not despair. An air mattress can be revived. We will teach you how to do this. So, our article is about how to seal an air mattress at home. Study the information and take it into account.

Repair kit

Air mattresses from well-known manufacturers are sold along with materials for restoration. They include special patches and instructions for their use. This is very convenient, because immediately after detecting a puncture in the mattress, you can fix it. But what to do if there is no branded repair kit or the patches have already run out? What and at home? We talk about this in the next part of the article.

Available means

When thinking about “Intex” or any other, let’s remember the materials that are in every home. With their help, you can eliminate problems on the PVC surface as easily and reliably as using a repair kit. For work we will need:

• pieces of thin rubber;
• acetone or gasoline;
• cotton pads;
• household gloves;
• brush;
• felt-tip pen;
• detergent (soap, shampoo);
• water.

How to seal an air mattress at home? Process description

First, you need to accurately determine the puncture locations. Soapy water will help you do this. Shake it until foam forms and use a brush to coat the surface of the mattress with this solution. In places where there are holes, circle these places with a felt-tip pen so as not to lose them.

Now the PVC surface needs to be degreased. To do this, moisten with gasoline or acetone and thoroughly wipe the puncture sites. Cut a patch from thin rubber the right size and also degrease it.

What glue should I use to seal an air mattress? We will do this with a “Moment”, but if you don’t have one, you can use any other fastening PVC product for these purposes. Apply this material to the surface of the patch and the puncture site. The glue layer should be of medium thickness. Wait about five minutes for it to react with the rubber and PVC. After this time, apply the patch to the damaged area and press firmly with your fingers. Leave this for a few minutes, and then place the mattress under a weight for a day. After drying, spread the repair area with soap foam to make sure that the patch is glued securely and no air escapes through it. If this is not the case and bubbles appear on the surface, then the work will have to be redone.

So you have learned how and how to seal an air mattress at home. We hope that now such a problem as a puncture in this product will not confuse you, and you will be able to fix it quickly and efficiently.