Section “Professions of workers common to all sectors of the national economy”((ETKS No. 1))

§ 192. Compressor unit operator (5th category)

5th category

Characteristics of the work. Maintenance of stationary compressors and turbocompressors with pressure up to 1 MPa (up to 10 kgf/sq. cm), with a flow rate of over 500 to 1000 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow rate of over 100 to 250 cubic meters. m/min. each when operating on non-hazardous gases and driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/sq. cm), with a flow rate of over 100 to 250 cubic meters. m/min or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow rate of over 5 to 100 cubic meters. m/min. every. Maintenance of automated compressor stations with a capacity of up to 100 cubic meters. m/min.

Switching and putting into reserve and for repair of compressor station equipment. Regulation of the technological process of production of station products. Drawing up defective statements for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a mechanic of the 4th category. Repair of compressors and engines internal combustion in the field.

Must know: kinematic diagrams of serviced compressors, turbochargers, steam engines, electric motors and internal combustion engines; compressor device high pressure; performance characteristics compressor and turbocompressor units, steam and electric engines for them and auxiliary equipment; diagrams of technological processes for production of the station product; efficiency of the compressors of the systems and structures used.

	(next) -->

Knowledge for the fifth category A mechanic of the fifth category must know internal organization good enough. Required knowledge:

• kinematic diagrams of turbocompressors, electric motors, steam engines, internal combustion engines;
• devices for compressors operating at high pressure;
• operating rules and characteristics of auxiliary equipment, steam engines, electric motors, turbocompressor units;
• technological processes of the station;
• Efficiency of the compressor and applied structures and systems.

Sixth category The work of a sixth category driver requires the greatest concentration, and knowledge must be supported not only by theory, but also by practice.

Job description for 6th category compressor unit operator

Compressor unit operator (4th category) Characteristics of work. Maintenance of stationary compressors and turbocompressors with pressure up to 1 MPa (up to 10 kgf/sq. cm), with a flow rate of over 100 to 500 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow rate of over 5 to 100 cubic meters. m/min. each when operating on non-hazardous gases and driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/sq.

cm), with a supply of over 5 to 100 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a supply of up to 5 cubic meters. m/min. every. Establishing and maintaining the most advantageous operating mode for compressors. Monitoring the serviceability of engines, compressors, instruments, auxiliary mechanisms and other equipment.

Production instructions for operators of compressor units (permanent)

Info

Knowledge of the types and types of instrumentation and instrumentation is required to perform the work efficiently. Knowledge of technological processes used in production is the key to successful work. It is also necessary to know the principles of operation of the installation, the structure of the compressor, electric motors, as well as the instruments used to carry out measurements.

Attention

Categories According to the reference book, there are 5 categories of compressor unit operators. Everyone has their own requirements for vocational training, and also describes the duties that an employee must perform in this position. The ETKS classifier distinguishes drivers of the second, third, fourth, fifth and sixth categories.

The second category is the highest; it has the highest requirements for experience and skills. The sixth, accordingly, is the lowest.

Compressor unit operator: description of the profession

MPa (over 10 kgf/sq. cm), with a supply of over 250 cubic meters. m/min. each when operating on non-hazardous gases and driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/sq. cm), with a supply of over 250 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow over 100 cubic meters. m/min. every. Maintenance of automated compressor stations with a supply of over 100 cubic meters.

m/min. Monitoring the operation of all compressor station equipment. Regulation of the technological process of production of station products. Drawing up defective lists for the repair of compressor station equipment.

Repair of compressor station equipment within the qualifications of a 5th category mechanic.

Compressor unit operator

A compressor unit operator of the 6th category carries out: 2.1.1. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/sq. cm), with a flow rate of over 1000 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow over 250 cubic meters. m/min. each when operating on non-hazardous gases and driven by different engines. 2.1.2. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/sq.

cm), with a flow of over 250 cc. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow over 100 cubic meters. m/min. every. 2.1.3. Maintenance of automated compressor stations with a supply of over 100 cubic meters. m/min. 2.1.4. Monitoring the operation of all compressor station equipment. 2.1.5. Regulation of the technological process of production of station products. 2.1.6.
A 2nd category compressor unit operator must be able to: 1. service stationary compressors and turbocompressors with a pressure of up to 1 MPa (up to 10 kgf/cm2) with a flow rate of up to 5 m3/min each when operating on non-hazardous gases driven by various engines; 2. start, regulate and stop compressors; 3. observe the operation of compressors and auxiliary equipment; 4. lubricate and cool the rubbing parts of compressor mechanisms; 5. General qualification requirements are given for all categories 6. prevent and eliminate malfunctions in the operation of compressors and monitor its operation safety devices; 7. maintain drive motors; 8. fill and pump oil into supply and emergency tanks; 9. participate in the repair of compressor station equipment; 10.

Error 404 page does not exist

CURRICULUM for advanced training of workers in the profession "Compressor unit operator" 3rd category Duration of training - 2.5 months No. Courses, subjects Total hours 1. THEORETICAL TRAINING 1.1 Fundamentals of market economics and entrepreneurship 16 12. General technical course 30 12.1 . Reading drawings, diagrams 8 1.2.2.
Materials science 8 1.2.3. Tolerances and technical measurements 8 12.4. Electrical engineering 6 1.3. Special course 92 1.3.1. Special technology 92 2. INDUSTRIAL TRAINING 242 Training time reserve 8 Consultations 4 Qualification exam 8 Total 400 QUALIFICATION CHARACTERISTICS Profession - compressor unit operator Qualification - 4th category A 4th category compressor operator must know and be able to fulfill all the requirements for 3rd category drivers.

Work instructions for compressor unit operator (6th category)

An employee is familiarized with this instruction upon acceptance (transfer) to work in the profession for which the instruction has been developed. 5.2. The fact that the employee has familiarized himself with these instructions is confirmed by a signature on the familiarization sheet, which is an integral part of the instructions kept by the employer. Developed by: Head of structural unit: . (last name, initials) (signature) » » g.
Agreed by: Head (specialist) of the labor protection service: . (initials, surname) (signature) » » d. Agreed by: Head (legal consultant) of the legal service: . (initials, surname) (signature) » » g. I have read the instructions: .
I APPROVED" Name of the employer's position (signature) (surname, initials) Date of approval Production instructions for the operator of compressor units (permanent) (name of profession, position or type of work) (designation) 2014 This production instructions for the operator of compressor units (permanent) is developed in accordance with ETKS 1, Design Rules and safe operation stationary compressor units, air and gas pipelines dated June 5, 2003 N 60. 1. GENERAL REQUIREMENTS 1.1. The operator of compressor units (permanent) is a worker and reports directly to the site foreman. 1.2. The operator of compressor units (permanent) must perform his duties in accordance with the requirements of these Instructions.
1.3.

6 documentation for compressor unit operator

For failure to perform or improper performance of their duties provided for in this job description - in accordance with the current labor legislation of the Russian Federation. 4.1.2. For offenses committed during the period of its activities - in accordance with the current civil, administrative and criminal legislation of the Russian Federation. 4.1.3. For causing material damage - in accordance with the current legislation of the Russian Federation. 4.1.4. For violation of internal labor regulations, fire safety and safety regulations established in the organization. 4.1.5. . 5. OPERATING MODE 5.1. The work schedule of a 6th category compressor unit operator is determined in accordance with the internal labor regulations established in the organization. Real job description designed in accordance with.

font size

UNIFIED TARIFF - QUALIFICATIONS DIRECTORY OF JOBS AND PROFESSIONS OF WORKERS - ISSUE 1 - SECTION PROFESSIONS OF WORKERS COMMON FOR ALL... Relevant in 2018

§ 193. Compressor unit operator

Characteristics of the work. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/sq. cm), with a flow rate of over 1000 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow over 250 cubic meters. m/min. each when operating on non-hazardous gases and driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/sq. cm), with a supply of over 250 cubic meters. m/min. or pressure over 1 MPa (over 10 kgf/sq. cm), with a flow over 100 cubic meters. m/min. every. Maintenance of automated compressor stations with a supply of over 100 cubic meters. m/min. Monitoring the operation of all compressor station equipment. Regulation of the technological process of production of station products. Drawing up defective lists for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a 5th category mechanic.

Must know: kinematic diagrams and design of turbochargers of various systems and types, power equipment: electric motors, steam engines, internal combustion engines; operational characteristics of compressors and power plants for them.

Note. An assistant driver of a compressor or turbocompressor station is charged two grades lower than the grade of the driver under whose supervision he works, but not lower than the 2nd grade.

Operators of mobile compressor units are charged according to the ETKS section “Construction, installation and repair work”.

§ 188. Internal combustion engine operator

6th category

Characteristics of work. Maintenance of installations or stations equipped with several internal combustion engines of various systems, total power from 2205 to 2573 kW (from 3000 to 3500 hp). Participation in dismantling, installation and testing of engines.

Must know

§ 188a. Internal combustion engine operator

7th category

Characteristics of work. Maintenance of installations or stations equipped with several internal combustion engines of various systems, with a total power of over 2573 kW (over 3500 hp). Participation in dismantling, installation and testing of engines.

Must know: design, electrical and kinematic diagrams of internal combustion engines various types; rules for dismantling, installation and testing of internal combustion engines.

§ 189. Compressor unit operator

2nd category

Characteristics of work. Maintenance of stationary compressors and turbocompressors with pressure up to 1 MPa (up to 10 kgf/cm2), with a flow rate of up to 5 m3/min each when operating on non-hazardous gases driven by various engines. Starting, regulating and stopping compressors. Monitoring the operation of compressors and auxiliary equipment. Lubrication and cooling of rubbing parts of compressor mechanisms. Prevention and troubleshooting of compressors and monitoring the operation of its safety devices. Maintenance of drive motors. Filling and pumping oil into service and emergency tanks. Participation in the repair of compressor station equipment.

Must know: operating principle of piston compressors, turbocompressors, steam engines and electric motors; methods for preventing and troubleshooting problems in the operation of compressors and engines; purpose and methods of application of instrumentation and control automation; compressor station piping diagrams; operating pressure in degrees and corresponding air temperature; permissible temperature heating of components of serviced units, measures to prevent and eliminate overheating; types and brands of oils used to lubricate mechanisms.

§ 190. Compressor unit operator

3rd category

Characteristics of work. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/cm 2), with a flow rate of over 5 to 100 m 3 /min, or pressure over 1 MPa (over 10 kgf/cm 2), with a flow rate of up to 5 m 3 /min each when operating on non-hazardous gases and driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/cm2), with a flow rate of up to 5 m3/min each. Starting and regulating operating modes of compressors, turbochargers and engines. Maintaining the required operating parameters of compressors and switching individual units. Detection and prevention of abnormalities in the operation of a compressor station. Maintaining reporting and technical documentation on the operation of serviced compressors, machines and mechanisms. Participation in the repair of compressor station units.

Must know: device of piston compressors, turbocompressors, internal combustion engines, steam engines and electric motors, their specifications and rules of service; pipeline diagram; device of simple and medium difficulty control and measuring instruments, automatic devices and fittings; reporting and technical documentation of the compressor station; fundamentals of thermodynamics and electrical engineering; properties of gases manifested during compressor operation.

§ 191. Compressor unit operator

4th category

Characteristics of work. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/cm 2), with a flow rate of over 100 to 500 m 3 /min, or pressure over 1 MPa (over 10 kgf/cm 2), with a flow rate of over 5 to 100 m 3 /min each when operating on non-hazardous gases driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/cm2), with a flow rate of over 5 to 100 m 3 /min or a pressure of over 1 MPa (over 10 kgf/cm2), with a flow rate of up to 5 m 3 /min each. Establishing and maintaining the most advantageous operating mode for compressors. Monitoring the serviceability of engines, compressors, instruments, auxiliary mechanisms and other equipment. Participation in the inspection and repair of equipment of compressor units within the qualifications of a 3rd category mechanic.

Must know: design features, device of various types of compressors, turbochargers, internal combustion engines, steam engines, steam turbines and electric motors, auxiliary mechanisms, complex instrumentation, apparatus and fittings; layout diagrams of steam pipelines, circulation condensation pipelines, fittings and tanks of the compressor station; layout diagrams of automatic devices for regulating the operation and blocking of equipment; main technical characteristics of the serviced compressors; energy consumption standards and operating materials for the production of compressed air or gas.

§ 192. Compressor unit operator

5th category

Characteristics of work. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/cm 2), with a flow rate of over 500 to 1000 m 3 /min, or pressure over 1 MPa (over 10 kgf/cm 2), with a flow rate of over 100 to 250 m 3 /min each when operating on non-hazardous gases driven by different engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/cm2), with a flow rate of over 100 to 250 m 3 /min or a pressure of over 1 MPa (over 10 kgf/cm2), with a flow rate of over 5 to 100 m 3 /min each. Maintenance of automated compressor stations with a capacity of up to 100 m 3 /min.

Switching and putting into reserve and for repair of compressor station equipment. Regulation of the technological process of production of station products. Drawing up defective statements for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a mechanic of the 4th category. Repair of compressors and internal combustion engines in the field.

Must know: kinematic diagrams of serviced compressors, turbochargers, steam engines, electric motors and internal combustion engines; installation of high pressure compressors; operational characteristics of compressor and turbocompressor units, steam and electric engines for them and auxiliary equipment; diagrams of technological processes for production of the station product; efficiency of the compressors of the systems and structures used.

§ 193. Compressor unit operator

6th category

Characteristics of work. Maintenance of stationary compressors and turbochargers with pressure up to 1 MPa (up to 10 kgf/cm 2), with a flow rate of over 1000 m 3 /min or pressure over 1 MPa (over 10 kgf/cm 2), with a flow rate of over 250 m 3 /min each at work on non-hazardous gases driven by various engines. Maintenance of stationary compressors and turbocompressors operating on hazardous gases with a pressure of up to 1 MPa (up to 10 kgf/cm2), with a flow rate of over 250 m 3 /min or a pressure of over 1 MPa (over 10 kgf/cm 2), with a flow rate of over 100 m 3 /min each. Maintenance of automated compressor stations with a flow rate of over 100 m 3 /min. Monitoring the operation of all compressor station equipment. Regulation of the technological process of production of station products. Drawing up defective lists for the repair of compressor station equipment. Repair of compressor station equipment within the qualifications of a 5th category mechanic.

Must know: kinematic diagrams and design of turbochargers of various systems and types, power equipment: electric motors, steam engines. internal combustion engines; operational characteristics of compressors and power plants for them.

Note. An assistant driver of a compressor or turbocompressor station is charged two grades lower than the grade of the driver under whose supervision he works, but not lower than the 2nd grade.

Operators of mobile compressor units are charged according to the ETKS section “Construction, installation and repair work”.

§ 194. Boiler room operator (stoker)

2nd category

Characteristics of work. Maintenance of hot water and steam boilers with a total heating output of up to 12.6 GJ/h (up to 3 Gcal/h) or maintenance in the boiler room of individual hot water or steam boilers with a boiler heating output of up to 21 GJ/h (up to 5 Gcal/h), operating on solids fuel. Maintenance of boilers for steam railway cranes with a lifting capacity of up to 25 tons. Lighting, starting, stopping boilers and feeding them with water. Crushing fuel, loading and drilling the boiler furnace. Regulation of fuel combustion. Monitoring the water level in the boiler, steam pressure and water temperature supplied to the boiler using control and measuring instruments heating system. Starting and stopping pumps, motors, fans and other auxiliary mechanisms. Cleaning boiler fittings and appliances. Maintenance of heating network boiler installations or compressed steam stations located in the service area of ​​the main units, with a total heat load of up to 42 GJ/h (up to 10 Gcal/h). Purification of crushed steam and deaeration of water. Maintenance set pressure and water and steam temperatures. Participation in flushing, cleaning and repairing the boiler. Manual removal of slag and ash from the furnaces and bunkers of steam and hot water boilers of industrial and municipal boiler houses and the blowers of gas generators, as well as from the grates, furnaces, boilers and blowers of steam locomotives. Layout of slag and ash dumps.

Must know: the principle of operation of serviced boilers, nozzles, steam-air ducts and methods of regulating their operation; construction of steam boiler furnaces, slag and ash bunkers, composition of thermal insulation masses and basic methods of thermal insulation of boilers and steam pipelines; purpose and conditions of use of simple and medium complexity instrumentation; arrangement of mechanisms for preparing pulverized fuel, tools and devices for cleaning nozzles and ash and slag removal; design and operating modes of equipment for heating network boiler installations or compressed steam stations; rules for cleaning grates, furnaces and boilers and smoke boxes of steam locomotives; permissible pressure and water level in the locomotive boiler during cleaning; the influence of atmospheric air on the condition of the walls of the firebox and fire box; procedure for refueling the firebox; basic properties of ash and slag; the order of movement of railway cranes on tracks and roads; rules for planning slag and ash dumps.

§ 195. Boiler room operator (stoker)

3rd category

Characteristics of work. Maintenance of water heating and steam boilers with a total heating capacity of over 12.6 to 42 GJ/h (over 3 to 10 Gcal/h) or maintenance in the boiler room of individual water heating and steam boilers with a boiler heating capacity of over 21 to 84 GJ/h (over 5 to 20 Gcal/h), operating on solid fuel. Maintenance of boilers on steam railway cranes with a lifting capacity of over 25 tons or boilers of steam excavators. Starting, stopping, regulating and monitoring the operation of traction and ash-slag removal devices, stockers, economizers, air heaters, steam superheaters and feed pumps. Maintenance of heating network boiler installations or compressed steam stations located in the service area of ​​the main units, with a total heat load of over 42 to 84 GJ/h (over 10 to 20 Gcal/h). Ensuring uninterrupted operation of boiler room equipment. Starting, stopping and switching of serviced units in heat pipeline diagrams. Accounting for heat supplied to consumers. Mechanical removal of slag and ash from the furnaces and bunkers of steam and hot water boilers in industrial and municipal boiler houses and the blowers of gas generators. Loading ash and slag using mechanisms into trolleys or wagons and transporting them to a designated location. Observation of proper work ash and slag removal mechanisms, lifting and transport equipment, alarms, instruments, equipment and fencing devices. Washing off slag and ash using special devices. Participation in the repair of serviced equipment.

Must know: arrangement of the equipment and mechanisms used; methods of rational combustion of fuel in boilers; diagrams of heat, steam and water pipelines and external heating networks; the procedure for recording the results of equipment operation and heat supplied to consumers; the importance of timely removal of slag and ash for the normal operation of boilers; rules for caring for serviced equipment and ways to eliminate deficiencies in its operation; types of boilers serviced; rules and methods for loading and transporting ash and slag; systems - lubrication and cooling of serviced units and mechanisms; rules for keeping records of the operation of mechanisms and equipment for ash and slag removal; installation of simple and medium complexity control and measuring instruments.

§ 196. Boiler room operator (stoker)

4th category

Characteristics of work. Maintenance of hot water and steam boilers with a total heating output of over 42 to 84 GJ/h (over 10 to 20 Gcal) or maintenance in the boiler room of individual hot water and steam boilers with a boiler heating output of over 84 to 273 GJ/h (over 20 to 65 Gcal/h) operating on solid fuel. Monitoring the water level in boilers, pressure and temperature of steam, water and exhaust gases using control and measuring instruments. Regulation of the operation (load) of boilers in accordance with the steam consumption schedule. Monitoring the fuel supply. Maintenance of heating network boiler installations or compressed steam stations located in the service area of ​​the main units with a total heat load of over 84 GJ/h (over 20 Gcal/h). Prevention and troubleshooting of equipment.

Must know: design and rules for servicing boilers, as well as various auxiliary mechanisms and boiler fittings; basic information on heating engineering, various fuel mixtures and the influence of fuel quality on the combustion process and the thermal performance of boiler units; fuel preparation process; technical conditions for water quality and methods of its purification; causes of malfunctions in the operation of the boiler installation and measures to prevent and eliminate them; device, purpose and conditions of use of complex instrumentation.

§ 197. Boiler room operator (stoker)

5th category

Characteristics of work. Maintenance of hot water and steam boilers with a total heating output of over 84 to 273 GJ/h (over 20 to 65 Gcal/h) or maintenance in the boiler room of individual hot water and steam boilers with a boiler heating output of over 273 to 546 GJ/h (over 65 to 130 Gcal/h) h) operating on solid fuel. Switching feed lines. Filling and emptying steam lines. Turning on and off automatic boiler power supply equipment. Preventive inspection of boilers, their auxiliary mechanisms, instrumentation and participation in scheduled preventive maintenance of boiler units. Receiving boilers and their auxiliary mechanisms from repair and preparing them for operation.

Must know: design and principle of operation of hot water and steam boilers of various systems; operational data of boiler equipment and mechanisms; device design automatic regulation; rules for maintaining the operating mode of the boiler room depending on instrument readings; diagrams of pipeline networks and alarms in the boiler room, rules for setting up and regulating instrumentation.

§ 198. Boiler room operator (stoker)

6th category

Characteristics of work. Maintenance of water heating and steam boilers of various systems with a total heating capacity of over 273 GJ/h (over 65 Gcal/h) or maintenance in the boiler room of individual water heating and steam boilers with a boiler heating capacity of over 546 GJ/h (over 130 Gcal/h), operating on solids fuel.

Must know: design features of complex instrumentation and automatic control devices; calorific value And physical properties fuel; elements of the fuel balance of boilers and its compilation; rules for determining the efficiency of a boiler installation.

§ 199. Crane operator (crane operator)

2nd category

Characteristics of work. Control of bridge and sluice cranes equipped with various lifting devices with a lifting capacity of up to 3 tons, when performing simple work for loading, unloading, reloading and transportation of bulk, piece, timber (up to 3 m long) and other similar cargo. Control of monorail trolleys, jib cranes and overhead cranes. Checking the correct fastening of cables, adjustment of brakes and operation of safety devices. Participation in the repair of a serviced crane.

Must know: design, principle of operation and operating rules of serviced cranes; maximum lifting capacity of the crane, cables and chains; rules for moving bulk, piece, timber and other similar cargo; system for switching on motors and controllers; basics of electrical engineering and plumbing.

§ 200. Crane operator (crane operator)

3rd category

Characteristics of work. Control of overhead and sluice cranes with a lifting capacity of over 3 to 15 tons, self-propelled self-climbing tower cranes, portal-jib cranes with a lifting capacity of up to 3 tons, tower stationary and gantry cranes with a lifting capacity of up to 5 tons, equipped with various lifting devices, when performing simple loading, unloading, reloading work and transportation of bulk, piece, timber (up to 3 m long) and other similar cargo. Control of overhead and sluice cranes with a lifting capacity of up to 10 tons, equipped with various lifting devices when performing work of medium complexity for loading, unloading, reloading and transporting timber (over 3 to 6 m in length) and other similar cargo. Installation of parts, products and assemblies on the machine, moving scaffolds and other installation devices and mechanisms. Control of electric hoists and portable cranes when performing all types of work.

Control of rack stacker cranes with a lifting capacity of up to 1 ton, equipped with various lifting mechanisms and devices, when performing work on placing cargo on racks, removing them from racks, delivering them to the loading area and placing them in containers, bags and pallets.

Must know: design and principle of operation of serviced cranes and their mechanisms; methods for determining cargo mass by appearance; rules for operating cranes for installing parts, products and assemblies on the machine; the procedure for loading racks with products in accordance with the established nomenclature and specialization; technological process of in-warehouse cargo processing; rules for stacking and storing cargo on racks; basics of electrical engineering and plumbing.

§ 201. Crane operator (crane operator)

4th category

Characteristics of work. Control of overhead and sluice cranes with a lifting capacity of over 15 tons, self-propelled self-climbing tower cranes, portal jib cranes with a lifting capacity of over 3 to 15 tons, tower stationary and gantry cranes with a lifting capacity of over 5 to 25 tons, equipped with various lifting devices, when performing simple loading and unloading work , reloading and transportation of bulk, piece, timber (up to 3 m long) and other similar cargo. Control of overhead and sluice cranes with a lifting capacity of over 10 to 25 tons, equipped with various lifting devices, when performing work of medium complexity for loading, unloading, transshipment and transportation of timber (over 3 to 6 m in length) and other similar cargo, installation of products, components and parts to the machine; tilting ship sections, moving scaffolds and other installation devices and mechanisms.

Control of overhead and sluice cranes with a lifting capacity of up to 10 tons, self-propelled self-climbing tower cranes, portal jib cranes with a lifting capacity of up to 3 tons, tower stationary and gantry cranes with a lifting capacity of up to 5 tons, equipped with various lifting devices, when performing complex work on loading, unloading, reloading and transportation timber (over 6 m long - on bridge and sluice cranes, over 3 m long - on self-propelled self-climbing tower, portal-jib, tower stationary and gantry cranes) and other similar cargo and cargo requiring increased caution, as well as when performing work on installation technological equipment and related structures, slipway and sectional assembly and disassembly of products, assemblies, assemblies, machines, mechanisms for landing and dispensing ingots and billets from heating furnaces, for pouring metal, for turning products and machine parts, forging with hammers and presses, installation of parts, products and assemblies on the machine that require increased care, and when performing construction, installation and repair work.

Control of cable cranes with a lifting capacity of up to 3 tons, equipped with various lifting devices, when performing all types of work.

Control of crawler and pneumatic wheel cranes with a lifting capacity of up to 10 tons, equipped with various lifting devices, when performing all types of work (except for construction, installation and repair work).

Control of rack stacker cranes with a lifting capacity of over 1 ton, stacker cranes with automatic control and overhead stacker cranes, equipped with various lifting mechanisms and devices, when performing work on loading, unloading, moving goods, laying them on racks, loaders and vehicles, for the delivery of goods from racks to production sites. Accounting for stored material assets. Control of cranes equipped with radio control.

Must know: arrangement of serviced cranes and their mechanisms; cargo processing methods; fundamentals of the technological process of installation of technological equipment, slipway and sectional assembly and disassembly of products, units, units, machines and mechanisms, structures of prefabricated elements of buildings and structures; determination of cargo weight by appearance; technical conditions and requirements for loading racks; location of serviced production areas; electrical engineering and plumbing.

§ 202. Crane operator (crane operator)

5th category

Characteristics of work. Control of overhead and sluice cranes equipped with various lifting devices with a lifting capacity of over 25 tons when performing work of average complexity for loading, unloading, reloading and transporting timber (over 3 to 6 m in length) and other similar cargo; installation of parts, products and assemblies on the machine; moving scaffolds and other installation devices and mechanisms. Control of tower self-propelled self-lifting, portal-jib cranes with a lifting capacity of over 15 tons, tower stationary and gantry cranes with a lifting capacity of over 25 tons, equipped with various lifting devices, when performing simple work on loading, unloading, reloading and transporting bulk, piece goods, timber (up to 3 m) and other similar cargo.

Control of overhead and sluice cranes with a lifting capacity of over 10 to 100 tons, tower, self-propelled self-climbing, portal and jib cranes with a lifting capacity of over 3 to 15 tons, tower stationary and gantry cranes with a lifting capacity of over 5 to 25 tons, equipped with various lifting devices, when performing complex work on loading, unloading, reloading and transportation of timber (over 6 m long - on bridge and sluice cranes, over 3 m long - on self-propelled tower cranes, portal jib, tower stationary and gantry cranes) and other similar cargo requiring increased caution, and also when performing work on the installation of technological equipment and related structures, slipway and sectional assembly and disassembly of products, assemblies, assemblies, machines, mechanisms for landing and dispensing ingots and billets from heating furnaces, for pouring metal, for turning products and machine parts and sections, including two or more cranes, when forging on hammers and presses, installing parts, products and assemblies on the machine that require increased care, when performing construction, installation and repair work.

Control of cable cranes with a lifting capacity of over 3 to 10 tons and floating cranes with a lifting capacity of up to 10 tons, equipped with various lifting devices, when performing all types of work. Control of crawler and pneumatic wheel cranes with a lifting capacity of over 10 to 25 tons and self-propelled railway cranes with a lifting capacity of up to 25 tons, equipped with various lifting devices, when performing all types of work (except for construction, installation and repair work). Control of crawler and pneumatic wheel cranes with a lifting capacity of up to 10 tons and self-propelled railway cranes with a lifting capacity of up to 15 tons, equipped with various lifting devices, when performing construction, installation and repair work.

Must know: design and kinematic diagrams of serviced cranes and mechanisms; technological process of installation of technological equipment, slipway and sectional assembly and disassembly of products, assemblies, units, machines and mechanisms, structures of prefabricated elements of buildings and structures; electrical engineering and plumbing.

§ 203. Crane operator (crane operator)

6th category

Characteristics of work. Control of overhead and sluice cranes with a lifting capacity of over 100 tons, equipped with various lifting devices, when performing complex work on loading, unloading, reloading and transporting timber (over 6 m in length) and other similar cargo, cargo requiring increased caution, as well as when performing work for the installation of technological equipment and related structures, slipway and sectional assembly and disassembly of products, assemblies, units, machines, mechanisms for landing and dispensing ingots and billets from heating furnaces, for metal pouring, for turning products and machine parts during forging with hammers and presses, installation of parts, products and assemblies on the machine that require increased care, and when performing construction, installation and repair work. Control of self-propelled self-lifting tower cranes, portal jib cranes with a lifting capacity of over 15 tons, tower stationary and gantry cranes with a lifting capacity of over 25 tons, equipped with various lifting devices, when performing complex work on loading, unloading, reloading and transporting forestry (over 3 m in length) and others similar cargoes, cargoes that require increased caution, as well as when performing work on the installation of technological equipment and related structures, slipway and sectional assembly and disassembly of products, assemblies, units, machines, mechanisms and when performing construction, installation and repair work .

Control of cable and floating cranes with a lifting capacity of over 10 tons, equipped with various lifting devices, when performing all types of work.

Control of crawler, pneumatic and self-propelled railway cranes with a lifting capacity of over 25 tons, equipped with various lifting devices, when performing all types of work (except for construction, installation and repair work). Control of crawler and pneumatic wheel cranes with a lifting capacity of over 10 tons and self-propelled railway cranes with a lifting capacity of over 15 tons, equipped with various lifting devices, when performing construction, installation and repair work.

Must know: device, kinematic and electrical circuits serviced cranes and mechanisms; location of serviced production areas; electrical engineering and plumbing.

Secondary specialized education is required when operating crawler and pneumatic wheel cranes with a lifting capacity of more than 200 tons when performing construction and installation work.

Notes: 1. When controlling overhead and sluice cranes with a lifting capacity of over 50 tons when installing powerful and heavy-duty turbo units, turbo generators, rolling and other similar technological equipment and related structures, when installing critical parts on large rotary, boring, lathe and other work machines are charged according to the 6th category.

2. This tariff does not apply to the work of crane drivers (crane operators) engaged in technological process main metallurgical industries of ferrous metallurgy (blast furnace, Bessemer, open-hearth, rolling, etc.) in metallurgical shops of machine-building enterprises, for work on pouring hot cast iron in specialized foundries for the production of molds, for work on electric bridge - stripper cranes when feeding poured molds onto gratings , removing the flasks and feeding the molds onto the cooling conveyor.

All of the above works and professions of crane operators (crane operators) are charged according to the relevant sections of the ETKS related to ferrous metallurgy.

3. Drivers working on tractors with cranes are charged according to the profession “Tractor Driver”.

4. An assistant driver of a self-propelled railway crane is charged two grades below the driver under whose supervision he works, and if he has the right to control and drive, he is charged one grade below the driver.

5. Drivers working on vehicles with cranes are charged according to the 3rd edition of the ETKS.

6. Loading and unloading work not related to the direct implementation of construction, installation and repair works are charged according to the corresponding complexity groups of loading and unloading work provided for in the characteristics.

7. Operators of self-propelled tower cranes with the crane cabin located at a height of 48 m or more are charged according to the 6th category, regardless of the crane’s lifting capacity.