In Russia, many houses are heated with gas. And no wonder. The deciding factor for most is the low price of fuel.

By the same logic, they usually buy a boiler. Foreign manufacturers, no doubt, can shine with both service and quality.

But the prices for their products are much higher than for domestic ones.

Gas boilers Russian production have a power of 11-68 kW and can be used in private homes, in agriculture and in industry.

First, let's figure out what kind of gas boilers there are.

Single and double circuit

A single-circuit boiler is intended for heating only. Double-circuit boilers will also provide owners with hot water. It is advisable to install such a boiler where the flow of heated water is small (if the flow is large, it is better to think about installing a single-circuit boiler with a boiler). The heat exchanger in double-circuit boilers can be bithermal or separate.

The principle of operation and connection of a single-circuit gas boiler

The first simultaneously heats water for heating and water supply. The second option is different heat exchangers, which extends the service life of the boiler. But, if it fails due to scale, the system will be left without heating! If we talk about cost, the bithermal option is cheaper.

A single-circuit boiler can be made with a boiler. It will provide the house with hot water, and the installation price is comparable to a double-circuit boiler.

Wall and floor

Wall-mounted gas heating boilers are mainly double-circuit and have a power of up to 20 kW.

Such a device is enough to heat a room up to 200m2, and they are much more attractive in appearance.

Traditionally, however, it is believed that wall-mounted appliances are best purchased for Not big houses, although many floor-standing units have less power.

A wall-mounted boiler is 2–2.5 times cheaper than a Russian-made floor-standing gas boiler. But according to statistics, ¾ of the boilers purchased in Russia are floor-standing.

Conventional boiler and condensing boiler

The condensing boiler has an additional heat exchanger in which waste gases are collected. Their heat can be said to be “secondarily” used by the device. Result: saving up to 30% gas. But harmful emissions are reduced by 70%. The efficiency is much higher.

Floor-standing condensing gas boiler

Installation and commissioning of boilers can only be carried out by specialists. In case of independent connection, at the first check, a fine will be imposed on the owner!

Popular Russian manufacturers

Several large enterprises produce gas boilers in Russia. Let's look at some of them.

ZhMZ

Zhukovsky Machine-Building Plant was founded in 1939 as an enterprise in the aerospace industry. Later, the production of AGV series boilers was launched, which were well received by the consumer. Today it is one of the most famous manufacturers of boiler equipment not only in Russia, but also in a number of foreign countries.

AKGV boiler from ZhMZ - diagram

Up to 30% of ZhMZ boilers have a power of 11 kW (this figure is easy to find out - look at the first digit in the name of the boiler). All ZhMZ boilers are floor-standing only.

Example: Boiler AKGV - 11.6 - 3. Its power is 11.6 kW. Weight – 35kg. Dimensions: 850x310x412 mm. Efficiency – 86%. The price varies from 10-20 thousand rubles.

Gas apparatus

A Russian-made double-circuit gas boiler can be purchased from OJSC Gazapparat; they produce popular double-circuit boilers Neva and NevaLux.

Example: Since 2007, the plant has been producing NevaLux - 8224 boilers. Installed in the combustion chamber water cooling so that scale does not form so quickly in the heat exchanger. The model was equipped with wider pipes. Reduced emissions carbon monoxide due to modernization of the burner. CO in flue gases is 10 times less than GOST allows.

The main advantage of a gas boiler is the availability of energy. : parameters of heating devices and installation rules.

About the construction of the furnace long burning read it yourself.

And here you will learn about the operating principle of automation for a gas heating boiler. What is its convenience? Types of automation.

Rostovgazapparat

CJSC Rostovgazapparat is another guard, founded in 1959 in Rostov-on-Don. Approximately half of the boilers produced by Rostovgazaapparat with heat exchangers made of steel or cast iron are boilers with a power of 23 and 29 kW. Automation in the units is imported. Models produced at the plant: AOGVK Rostov, KGDO Siberia, AOGV Rostov Siberia.

Conord

The Rostov company produces double-circuit Don boilers with a capacity of 16, 20, 31 kW.

In addition to the fact that the boilers operate on different fuels, they are equipped with the following useful functions: automatic ignition, a “high/low flame” function, which allows you to save up to 20% of gas.

Replaceable coil. This part quickly breaks down and it is very convenient that it can be easily replaced.

Borinskoe

OJSC "Borinskoe" received its name from the village where the plant has been located since 1976. The company produces both gas boilers, as well as solid fuel and universal ones. Some models, for example, EuroSit, use imported automation.

The most popular models and prices

Prices for Russian-made gas boilers vary depending on the manufacturer.

ISHMA BSK from JSC Borinskoye. Double-circuit gas boiler 12.5 kW, designed for 120 m 2 area. Gives water temperature – 95 0 C. Price – approx. 17,000 rub. The heat exchanger is copper and does not depend on electricity.

Danko 10X from “Agroresurs”

Danko 10U from Agroresurs CJSC. Single-circuit boiler 10 kW, designed for 90 m 2 area. Gives water temperature – 90 0 C. Price – approx. 14500 rub. Steel heat exchanger, does not depend on electricity.

"Don 50" is a universal floor-standing boiler with an efficiency of 85%. Power – 50 kW, designed for an area of ​​up to 500 m 2. Gas consumption per day is about 9 m3. Does not depend on electricity.

Advantages and disadvantages of domestic equipment

Domestic manufacturers, when developing their products, focus not on style and fashionable technologies, but on quality and adaptation to local conditions. And therefore Russian boilers:

• Adapted to climate, temperatures, pressure differences in the main line.
• Easy to maintain.
• Repairable, spare parts are easier to buy.
• They run on bottled gas - they can be installed where there is no mains.
• Huge price difference! Russian boilers are two or even three times cheaper than similar imported ones.

Our boilers have disadvantages in comparison with foreign units, but it depends on how you look at it...

1. Imported boilers are more advanced in terms of automation, electronics, they can regulate temperature up to half a degree, etc. But sometimes, in our conditions, they quickly break down or cannot use all functions at full capacity.
2. Domestic boilers are bulky, more like an industrial unit than an appliance for the home. The imported model will fit into modern design. But sometimes beauty is not needed in such technology. Especially if there is a separate boiler room. In addition, the latest models of many domestic factories have noticeably decreased in size and, apparently, they are also working on the design.
3. Russian boilers generally operate less efficiently and have lower environmental friendliness. But this does not apply to all devices. Some of our companies are working on improvements in this area.

If you want to choose a sauna boiler according to special parameters, then it’s easier to make it yourself. You'll save money and get exactly what you need. : step-by-step instruction on production.

Which stove is better for a dacha: Russian, Dutch, or maybe a fireplace stove? We will look at all types of stoves and figure out which one is more appropriate to install.

Which model should you choose?

Which boiler model is right for your particular case will depend on many factors.

Try to weigh them and take them into account. Having decided whether the boiler will be floor-standing or wall-mounted; single-circuit or double-circuit, you need to calculate the power.

An approximate calculation can be made for a house with well-insulated walls and ceilings of about 3 m. For 10 m2, 1 kW of power will be required.

Pay attention to what gas pressure in the network the device is designed for. If, for example, it is 20 mbar, and the actual pressure in the line is 10 mbar or less, then the unit will not operate at full capacity, and there is no point in overpaying for this power.

Is the unit dependent on electricity? Many imported models are equipped with pumps, fans, programming... all this is good if you never have power outages. If breakdowns occur and planned outages, then it is better to purchase a simpler but reliable device. Most Russian boilers do not depend on electricity.

Read the reviews. There are sites that specialize in reviews, where you can find the opinions of the owners of a particular model.

Heating system of a private house - calculation of a gas boiler

Is there a repair shop or service center near you? A private conversation with masters can give a lot. Ask them - which boiler models are most often brought in for repairs? What breaks and how much does it cost to fix?

So. Russian-made gas heating boilers cannot please you with their beauty and fine settings. But reliability and endurance in the most difficult working conditions are the trump card of domestic technology. And most importantly, the price is noticeably lower.

Video on the topic

Many of my friends have a Danko boiler and the reviews are contradictory. On the one hand, it is reliable and durable, only requiring periodic cleaning. On the other hand, it’s not entirely economical.

For some reason, I don’t trust such things to our Russian manufacturers. Maybe I’m wrong, but in my opinion, our country still has too little experience in the manufacture of gas boilers. Most likely I'm wrong. But somehow I don’t have confidence.

• For some reason, I don’t trust such things to people like myself, Russians, Russian manufacturers. Maybe I’m wrong, but in my opinion, our country still has too little experience in manufacturing gas boilers, since we are not a gas country at all. We heat with anything, but not with gas. And besides, they don’t mine it here, maybe I’m wrong. Most likely I'm wrong. But for some reason I have no confidence, no brains, and no common sense. And in general I'm an eccentric.
  –

Are you planning to buy a gas boiler? The Termomir online store offers a wide selection of heating and water heating equipment from leading Russian and foreign manufacturers.

Our catalog contains the following types of gas boilers:

• Dual-circuit. Do you need a gas boiler to heat your private home? The dual-circuit device will become good choice for home or garden: a heating boiler of this type, in addition to being used for its intended purpose, can work as instantaneous water heater, providing the room with hot water. IN summer mode heating water does not require heating to be turned on!
• Single-circuit. Single-circuit heating boilers are designed for heating premises, however, when purchasing an indirect heating boiler (in some models it is included from the factory), they can perform the functions storage water heater. It should be noted that this function does not affect the quality of heating in any way. Gas heating boilers in summer time can only operate in water heating mode.

You can buy a boiler of both wall-mounted and floor-standing types:

• Floor-standing gas boilers for a private home, the prices of the initial models of which are quite low, are distinguished by good performance indicators, reliability, unpretentiousness, environmental friendliness and a truly long service life. A foreign-made heating (gas) boiler can easily be in operation for 50 years or more. Among the disadvantages, it is worth noting the need for separate room with quality ventilation system, as well as a channel for removing flue gases.
• Wall-mounted gas boilers in Belgorod are very popular. Their main advantage over floor-standing analogues is their low requirements: their operation does not require a separate room equipped for a mini-boiler room.

In addition, our catalog contains spare parts for gas boilers, as well as accessories for them in a wide range.

You can buy a gas boiler in Belgorod without leaving your home, directly on the website of the Termomir online store. Are you looking for a specific wall-mounted or floor-mounted gas boiler for a private home? Price, boiler type and other parameters are set using a special filter on the left side of the site. Knowing exactly what you need, you will quickly and easily find it in our catalog.
Poor understanding of the topic? Don't know what is best to choose specifically in your situation? Do you see similar gas boilers, the prices of which differ significantly, and you don’t understand why? Just call the number indicated in the header of the site and our specialists will help you choose the equipment that is optimal for solving your specific problem absolutely free of charge. You can place your order immediately!

We remind you that a delivery service is available for residents of Belgorod and the region. You can find out more details by contacting our operator or visiting the appropriate section of the site.

Gas boilers are perhaps the most popular of all existing boiler models. They are wall-mounted and floor-mounted. The range of such boilers is very wide. Conventionally, they can be divided into the following groups according to price categories: the most expensive and high-quality, average cost and inexpensive boilers.

Accordingly, the quality of the boiler and its service life depend on the price. Russian-made boilers are relatively inexpensive compared to imported boilers.

Producing countries of gas boilers

The first step in the quality rating is occupied by boilers that are produced in Germany, Austria, and France. Boilers good quality countries such as Italy, Spain, Belgium, England, and Slovakia produce at quite affordable prices.
The most inexpensive category includes domestic floor-standing gas boilers.

The most famous Russian-made gas floor-standing boilers are those produced at the Zhukovsky Machine-Building Plant.

This plant produces the following series of gas boilers:

• Economy series.
• Station wagon.
• Comfort.

In Taganrog there is a plant for the production of boiler equipment - Lemax. The models produced at the plant consist of imported components and run on both gas and solid fuel. Lemax produces single-circuit and double-circuit boiler models. The most popular models from the manufacturer Lemax: Leader, Gazovik, Plus.

There are other manufacturing companies in Russia heating equipment: Mimax plant (Taganrog), Rostovgazapparat company.

Complete set of domestic gas boilers. Types of boilers

Domestic gas floor heating boilers are equipped with all the necessary components: heat exchanger, chimney, draft sensor, heating pad, air vent, safety thermostat and valve. All components come with the boiler.

Floor heating systems are classified as follows:

1. There are double-circuit and single-circuit models of gas boilers.
2. According to the type of combustion product removal chamber, boilers are divided into boilers with an open chamber and boilers with closed camera.
3. There are boilers with natural and forced circulation air.

Pros and cons of gas boilers from a Russian manufacturer

Preference is always given to imported products.

It’s better to pay more and get reliable equipment than to save money and get a bunch of problems.

A floor-standing domestic gas boiler made in Russia has its own positive and negative characteristics.

The advantages include:

• of course, the price of domestic gas boilers;
• optimal efficiency;
• huge service base - necessary or broken parts can be found in all cities of the country;

But there are also undeniable disadvantages of this equipment:

• large weight and dimensions of the boiler;
• out-of-date design;
• lack of temperature control in the heating system.

Having studied the characteristics of gas boilers from a domestic manufacturer, you can make a choice in favor of one model or another.

On this tab we can determine certain structural components for the desired garage. The garage heating assembly has some components. Each element is very important. Therefore, the selection of each element of the system must be done correctly. The heating circuit includes a connection system, pressure-increasing pumps, fasteners, pipes, thermostats, batteries, an expansion tank, manifolds, and a boiler.

Russian-made gas floor-standing boilers are also produced by ZIOSAB Closed Joint Stock Company. The plant produces over 15 models of boilers. The plant produces boilers such as own production, and under license from the Finnish company Finraila.

CJSC ZIOSAB produces boilers taking into account world standards of boiler construction, both minimum power and fairly powerful boilers with a value range of up to 3000 kW.

According to consumer reviews, Russian-made gas floor-standing boilers are not able to compete with European manufacturers.

Russian manufacturers of gas boilers

In Taganrog there is a plant for the production of boiler equipment - Lemax. The models produced at the plant consist of imported components and run on both gas and solid fuel. Lemax produces single-circuit and double-circuit boiler models. The most popular models from the manufacturer Lemax: Leader, Gazovik, Plus.

There are other companies in Russia that manufacture heating equipment: the Mimax plant (Taganrog), the Rostovgazapparat company.

Complete set of domestic gas boilers. Types of boilers

A wall-mounted boiler is usually considered compact, and this is, to some extent, true. For example, Buderus floor-standing gas boilers will be 30 percent more than the wall-mounted range from the same manufacturer. Such devices have three mandatory elements: gas burner, fittings for regulating the gas supply and the heat exchanger itself. You can find steel and cast iron heat exchangers, but due to their greater weight and high cost, they are still preferred to be replaced with copper ones. Also, do not forget about the built-in boiler automation.

Additionally, any wall-mounted device contains a built-in pump that drives water along the circuit, an expansion tank and safety valve. A control, protection and self-diagnosis system is required. It “vigilantly” monitors the condition of the fuel: if there is a leak or lack of gas, the automation stops operation and gives a signal about a malfunction. A Zhukovsky floor-standing gas boiler (or a floor-standing unit from any manufacturer) will work in exactly the same way.

Mini-boiler rooms located on the floor have essentially the same device as wall-mounted units. They are based on the same heat exchangers, usually installed from a copper composition (in case of operating errors and for reliability, they are often used steel structures). Two types of burners are installed in gas floor heating boilers: atmospheric and forced (also called mounted, fan, replaceable). Atmospheric ones are somewhat cheaper and operate silently. The mounted structure is more powerful and works with full efficiency, but its price is always higher. As a rule, Ferrol boilers are purchased with these parameters - they have proven themselves in both quality and design.

Floor-standing gas boiler: how to choose the right one

The choice, first of all, should be made taking into account both the expected area for heating and the power level, which does not always mean the same thing. If there is a lack of space, also in small rooms located in middle lane, you can get by with a regular mounted boiler. But in the case of a house built in a cold climate with great need For heating, it is better to choose a more powerful unit. Prices for floor-standing gas heating boilers are higher, but the operating efficiency will be appropriate.

By the way! Wall-mounted devices are considered the cheapest (installation can cost up to $1000), easy to install, and suitable for small spaces.

Quite often they are single-circuit, which only allows heating the room; to heat water, for example, you will need a boiler. Of course, there are also floor-mounted single-circuit gas boilers, but even their heating power is significantly higher. This wall mounted boiler will suit the owners small house that use other means to heat water: a boiler, a water heater, a fireplace with a water circuit, etc.

Most owners of private households with an area of ​​200 square meters or more will prefer floor option with power control. These extremely reliable devices (with the same “filling” as the mounted unit) require maintenance approximately every three years and provide greater power. Their cost is higher, especially if it is a double-circuit gas boiler, floor-mounted or wall-mounted. In principle, it does not matter, one piping of a floor-standing gas boiler will cost at least 500-600 USD. but subsequent minimal expenses for household services compensate for this.

Typically divided into two directions

Floor-standing units with a double circuit will be beneficial to owners of large houses that were “conceived” without connection to central system initially. Single-circuit floor-standing gas boiler - not the best convenient option, since you have to branch out the system even more when you turn on, for example, speakers. Although the dual-circuit system does not allow operating in heating and water heating modes simultaneously, this is leveled out thanks to the simple laws of physics.

Russian floor-standing gas boilers today are presented in a wide range of products, among which you can find fairly inexpensive options that are acceptable for many domestic families. What is characteristic is that today these neat devices are no “stupid” than their foreign counterparts. It is also worth noting that in the domestic market, industrial gas boilers are gaining no less popularity than household ones.

By the way! They are equipped not only with high-quality circuit boards, but also with weather-dependent automation, which allows you to keep the temperature in the house from changes even before it changes indoors.

For example, Lemax floor-standing gas boilers with a similar modern thermostat “subtly” sense weather conditions. To do this, their temperature sensors are also taken outside. The devices measure the temperature there, and based on these readings, the floor-standing boiler can be reprogrammed in advance for changes in the microclimate in the house itself.

A little more about Russian production

Other Russian high-quality floor-standing gas boilers “Buderus” allow you to adjust the “weather in the house” for a certain period of time, setting indicators. For example, during the week the owners will not be at home more often than usual, so you can reduce the power of the boiler. And for the Christmas holidays, all family members will gather in the family nest - the boiler is programmed to work with maximum efficiency. This makes the life of the owner of a private home much easier: he does not need to worry about the temperature in the house, he only needs to spend 15 minutes on weekends setting up the thermostat.

Reviews for domestic floor-standing gas heating boilers are usually positive. This suggests that Russian craftsmen have long learned to produce beautiful, high-quality and, most importantly, reliable products with excellent automation. Also, purchasing such boilers can be significantly cheaper, and servicing of Russian equipment will be carried out by specialists from the manufacturing plant itself. They know their product better than anyone else, and you won’t have to wait a long time for repairs - all the spare parts are “at hand”, and not in a foreign company.

When choosing a boiler for heating, there are a number of points that are worth paying attention to, especially since there are many companies on the manufacturer’s market that offer such products. Russian-made wall-mounted gas boilers are no different in their characteristics than foreign ones, but at the same time they are much cheaper.

When choosing such a product, you should take into account such points as further installation methods, power, room size and a number of other points that you may need, especially since now there are a number of products that can work not only as heating boilers, but also as a device for heating water.

Rice. 1

Characteristics of devices for fuel materials

Based on heating materials, boilers can be:

• Solid fuel.
• Gas.
• Electrical.

Solid fuel boilers mainly used for large premises and larger private houses, for example, for small apartment such a device cannot be used. Solid fuel boilers generally require separate rooms in which they can be placed and operate without harming the residents of the house.

Gas boilers can be the most different sizes and have a number of additional functions. Such a heating boiler can fit in a small bedside table in even the smallest apartment. A gas boiler can have one circuit or two. So a device with one circuit will be used only for heating the room, while a device with two circuits can not only heat the room, but also serve as a means for heating water.

Electric boilers According to the gas type, they can operate on one circuit or two. But you need to pay attention to the amount of costs. The positive aspect of using electrical equipment is the absence of emissions.

Power selection

Rice. 2

The power of the boiler itself must be selected based on the size of the room. There are a number of mathematical calculations that can be used to accurately determine the power required for your premises. To accurately calculate the required power, you need to take into account only the area itself, but also pay attention to the height of the ceilings.

If the ceilings are too high, the power of the equipment for quality heating there should be more.

In addition, it is necessary to take into account the amount of heat loss from the room itself. This indicator is measured depending on the insulation of the room. Thus, a well-insulated room can use much less money for heating and the required boiler power can be sufficient up to 70 W/m2.

The second point that you should pay attention to when choosing a dual-circuit device is the power when heating water. When heating water, you need a unit with a power of 24 W/m2. Gas boilers with such power are among the most popular of all types of domestic production.

Choice of equipment: single-circuit or double-circuit

Rice. 3

The choice of heating boiler depends on the needs that you need to satisfy. If the feed warm water into the room is impossible or such supplies do not suit you, then when installing a heating device, it is recommended to pay attention to double-circuit gas boilers.

Russian wall-mounted gas heating boilers are often used in apartments. Such devices have good power and can work efficiently in small spaces; in addition, they do not require separate rooms for installation and are completely safe for home residents.

Wall-mounted double-circuit gas boilers of domestic production include a reliable water heating system for heating the room, and also have a built-in boiler, which can heat water for home use without additional external devices. The advantage of domestically produced double-circuit boilers is that they are quite compact for small spaces, which is very convenient for use in an apartment.

Single-circuit units, both domestic and foreign, can heat water only for heating purposes.

Rice. 4

Types of boilers for removing combustion products

According to the methods of removing combustion products, gas boilers can be divided into:

• Chimneys.
• Turbocharged.

Chimney gas boilers use natural exhaust hoods to remove combustion products. To install such a unit indoors, you must have a high-quality chimney in the room. As for many apartments in our country, and especially in houses that are more than twenty years old, there is no way to guarantee high-quality removal of combustion products from the device.

Initially, such houses were not intended for the installation of individual heating devices. Thus, when using chimney boilers, there is a possibility of exhaust entering the living space. Such boilers use an open combustion chamber in their operation, which in turn requires large quantity oxygen in the room. Therefore, it is also not recommended to install them in a residential area, but a separate boiler room.

Rice. 5

In this connection, Russian-made factories offer users to choose turbocharged boilers. Turbocharged units operate with a closed combustion chamber. In addition, the positive aspects of such devices is that the removal of combustion products is forced, which guarantees high-quality removal carbon dioxide from the living room using the built-in fan.

In most cases, such boilers for heating premises require the installation of separate pipes that will be led from the premises to the street. Often a coaxial pipe is used; such a pipe contains air supply to direct it. Hot exhaust gases are discharged through the inside of the pipe.

The internal part supplies air to the combustion chamber. A positive aspect when installing such a device is the absence of a chimney; for them it will simply be enough to lead a large pipe through a hole in the wall to the street.

Types of boilers by installation methods

By installation method heating devices can be divided into:

• Wall-mounted.
• Floor-standing.

Domestic wall-mounted gas boilers are very popular for small spaces and apartment buildings. The bulk of these gas boilers are divided depending on the materials from which they are made. The production of wall-mounted units uses a copper heat exchanger, while the production of floor-standing equipment uses a cast iron heat exchanger.

The positive aspects when using a copper heat exchanger is their weight, namely the weight of such equipment will be about thirty or forty kilograms. The light weight of such a device will allow you to place it in a small room. In addition, the power of such devices is up to 35 kW, this power is quite enough for a small apartment or even for a medium-sized house.

But there is a small disadvantage in the production of such devices; their service life is limited; more information on the service line is provided by the manufacturer himself. A positive aspect in the production of such equipment is their compactness; such a small device can accommodate a pump, expansion tank, safety group and much more.

Floor-standing gas boilers with a cast iron heat exchanger, despite their longer service life, require the purchase of many additional auxiliary elements for installation and further operation. It is also worth paying attention to the weight and dimensions of the device.

The weight of equipment with a cast iron heat exchanger can be up to one hundred kilograms, and some devices can exceed one hundred and fifty kilograms. Such units take up quite a lot of space and require installation in a separate room.

The positive aspect is high-quality and long-lasting heating.

Cost-effectiveness of Russian-made wall-mounted boilers

Rice. 6

Among modern gas appliances, the majority have an efficiency of eighty-nine to ninety-three percent. In addition, the problem of heat loss during heating can be solved by insulating the room itself. If the issue of saving is significant for you, then at the time of heating it is worth installing temperature sensors. Among the variety of Russian-made equipment, there are a number of quite economical options.

For example, when using a temperature sensor for gas equipment you can set two heating modes, one of which will be aimed at heating the room when there are residents in it, and the second option is more economical, which will simply maintain a certain temperature regime, and will raise the temperature in the room before the owners return.

Russian-made gas boilers have additional functions, when using which you can set such heating modes. In addition, you can set an economical heating mode at the time of sleep. When using such room heating modes, savings can amount to about thirty percent.

Using automation in wall-mounted appliances

Safety in the production of devices such as gas boilers for space heating is of great importance. When developing gas boilers high level safety can be ensured by using a self-diagnosis system. Self-diagnosis for gas boilers can independently turn off the power in such cases as flame entry, lack of or insufficient combustion waste removal, water overheating, change in water pressure, insufficient fuel supply or unstable energy supply.

Such a security system is necessary especially for wall-mounted heating boilers, which can be placed in a residential area where people are constantly present. Such devices can be found among Russian manufacturers. In addition, Russian production allows such devices to independently resume their operation after the situation has stabilized, or it is possible to set the settings in such a way that users will need to turn it on again. Such security systems are aimed at the complete safety of people.

New types of boilers

Recently, production of new generation devices has begun in Russia. This invention was condensate wall-mounted boilers Russian production. A positive aspect in creating such products is a high level of efficiency. The efficiency level of Russian-made wall-mounted gas units can be one hundred and ten percent.

They are made from of stainless steel, can work for a long time. Compared to conventional gas boilers, their service life has increased two or even three times. This result was achieved through the use of high-quality stainless steel. Wall-mounted gas boilers made of stainless steel, with their compact size and light weight, can provide the user with operating power of up to 100 kW.

There is only one drawback in the production of such wall-mounted gas boilers; the waste products from such a heating device must be discharged into the sewer system.

The choice between domestic and foreign manufacturers

If you have decided on the basic requirements for the wall gas boiler For space heating, the next step is choosing a manufacturer. The first thing you need to pay attention to is the cost of a foreign-made product. The bulk of foreign-made equipment is created using a large number of electronic devices. The negative aspect of such production is its service maintenance.

So, for example, if a malfunction occurs, you will need to call a technician to remove the problem.

Wall-mounted gas boilers, which are foreign-made for heating premises, require constant diagnostics and programming. Thus, to service such a product, it is always necessary to have a technician who can come at any time and fix the problem.

Wall-mounted gas boilers of foreign manufacture are not adapted for heating our premises and for domestic system gas supply. In connection with this, there is no point in buying equipment in Russia that will be much more expensive and quite capricious. Therefore, many experts recommend buying domestic gas appliances from Russian manufacturers for use in Russia.

When choosing Russian-made gas boilers, you can get full advice throughout Russia, find good master, who can not only install your device, but also carry out further maintenance and such a gas appliance can last much longer. In addition, wall-mounted gas appliances are in greater demand in Russia than abroad, and therefore much more attention is paid to their development. Such units are adapted for heating homes and apartments in Russia.

If you have chosen a foreign-made product, then you should take into account the permanent problems with the supply of gas and electricity that exist in Russia. Therefore, it is worth paying attention to wall-mounted gas units, which, after power is supplied, can resume their operation on their own, such as wall-mounted gas boilers for heating premises made in Russia.

Rice. 7

Manufacturers of gas boilers

In Russia there are many manufacturers who make high-quality wall-mounted and floor-mounted gas appliances for heating rooms of any power.

Among them:

• JSC Zhukovsky Machine-Building Plant;
• CJSC "Rostovgazapparat";
• LLC "Plant Conord";
• OJSC "BMZ-Vikma";
• OJSC "Borisoglebsk Boiler and Mechanical Plant";
• OJSC SEZ "Energochast";
• OJSC "Krasny Kotelshchik";
• JSC "Borinskoye";
• OJSC "Neva Lux".

These manufacturers have won many wonderful awards, which they received not only in Russia, but also outside the country. Such units can have many functions, while they have good power, last a long time and are not demanding to operate. These manufacturers are one of the best in the manufacture of wall-mounted and floor-mounted gas appliances for heating apartments and houses.

Manufacturer "Neva Lux"

One of such manufacturers is Neva Lux OJSC. The manufacturer offers big choice wall-mounted gas boilers for heating any premises, these gas appliances can be used both for heating small spaces in houses or apartments, but also in production for heating work premises.

Except quality production the company also offers to inspect the premises by engineers who are ready to select the most suitable wall-mounted gas boiler for home heating for the user. Then the company carries out installation of the gas unit and further maintenance. Providing engineering consultation allows the user to choose the most suitable option that will provide high-quality heating of the room and lead to the lowest possible costs.

For construction companies and co-owners of apartment buildings, as well as new buildings, proposes to organize the apartment-by-apartment installation of a heating system using wall-mounted gas boilers.

The Neva Lux company is one of the most famous in Russia and produces the highest quality wall-mounted gas boilers for heating, according to consumers.

Zhukovsky Machine-Building Plant

Another manufacturer of wall-mounted and floor-mounted gas boilers for space heating is the Zhukovsky Machine-Building Plant. This plant has been operating for more than forty years, and during that time many gas appliances have been produced that have been operating in the houses and apartments of citizens of the federation for a long time. The power of gas boilers can range from eleven kW to sixty-eight. In this connection, this gradation allows the use of their gas boilers for heating the most different rooms.

The equipment produced at the Zhukovsky Machine-Building Plant has good automation. This automation allows wall-mounted gas boilers to provide the necessary level of user safety.

Devices from this manufacturer are divided into three types:

• Economic.
• Universal.
• Comfort.

Thanks to this, it is possible to choose a wall-mounted gas unit for heating any room. In addition, the latest combustion systems are used and the efficiency of these devices is at least eighty-nine percent.

LLC "Plant Conord"

This plant produces heating systems not only for residents of the country, but also works with foreign buyers. Conord wall-mounted gas boilers use special technologies in the manufacture of wall gas heaters. This is achieved using an enlarged magnesium anode. In addition, this technology avoids overheating. Thanks to the use of such technologies, wall-mounted gas appliances from this manufacturer are popular not only in the national market, but also outside the country.

OJSC "Krasny Kotelshchik"

This is an open joint stock association that was created on the basis of several individual factories that have been working on the production of heating systems for a long time. At the moment this plant is one of the largest in the territory Russian Federation.

The plant produces many goods to order for foreign partners. It has many quality marks and insignia, and most importantly, all products are manufactured on the basis of GOST standards.

The choice of heating system is very important. The first thing you need to pay attention to when making such a choice is your safety. You can achieve this by choosing a heating system that has automatic diagnostics. Also, do not forget that the removal of combustion products must be carried out efficiently. After this, when choosing heating systems, do not forget that you need to calculate required power. Choose the device that best suits your requirements.