DIY children's slide made from pipes. Children's wooden slide for the dacha - instructions for making it yourself. What do you need for a slide?

Children's slide for the dacha: the product we will talk about in this article on the website. Drawings photos and video instructions will help you build DIY children's slide. A children's slide is probably one of the mandatory elements of any summer cottage if you have children. Any number of structures can be installed on the playground various types: sandbox - the choice depends on your desires and financial capabilities. Most items for the playground can be made independently. For example, children's slide It is constructed quite simply, and has served as a source of children's joy for many years.

The main requirement for children's slide at the dacha is safety

Mandatory conditions for a children's slide in the country

Children's slide at the dacha can be installed both indoors and outdoors. It is worth understanding that the slide is for a child (whether it was built for a home or for an outdoor in this case does not matter) must meet certain requirements:

For construction, you need to use only environmentally friendly materials that are safe for the health of the child. It doesn’t matter whether you are building a slide from wood, metal or plastic, the material should not contain harmful elements. The same goes for paint and varnish materials, with which you will open the structure. Another important point both for a children's plastic slide for the home and for a wooden structure - it is fire resistant;

The most popular materials for slide construction– wood and metal

be sure to use structural elements such as railings and fences. They will not only help the child maintain balance while climbing the slide, but will also protect him from falling during games. Railings on a slide for a child in the country should be installed regardless of the age of your child;
It is best to use wood to build the structure. Children's wooden slides for the home are more pleasant to use due to the natural origin of the material. IN street conditions Wooden slides do not heat up as quickly as metal ones, so they can be installed in any place convenient for you, and not just in the shaded part of the site. A child can easily get burned on hot metal, but wood does not heat up to a dangerous temperature;

Metal slide with a wavy slope covered with acrylic paint

plastic children's slide easier for the street than wood or metal. It can be easily moved from place to place and transported if necessary, but the material itself is less durable and can easily crack;
slide should be located away from trees, lamps, outbuildings and other structures. This is done so that the baby does not get hurt when going down the slide. The surface around the hill can be sown lawn grass or use a special rubber coating. Remember that the main thing is the child’s health, so any street children's slide for the garden must be safe;

Slide must be installed on open area, which will help minimize possible injuries

the base should be strengthened with a metal support or concreted. You should not rely on the fact that the child will not move the structure from its place - even the most durable slide can tip over as a result of children's games;
an important point is the height of the structure being constructed do-it-yourself children's slide for the dacha. It must be appropriate for the child’s age, for example, the height of a slide intended for younger children school age, should not exceed 3.5 m.

Wooden slide with two slopes, a house and a swing, built in the courtyard of a private house

Helpful advice! The design of the slide must have no gaps or openings, otherwise the child may get stuck or be seriously injured during the game.

DIY slide construction: materials and tools

How build a slide at your dacha with your own hands without special labor? If we are talking about a wooden structure, you will need several wooden beams, planed boards, slats, lining and fiberboard. You can connect the elements together using nails, anchor bolts and screws.

Process construction of a children's slide made of wood

The list of tools needed for construction is very simple:

wood saw, manual or electric;
hammer;
hand or electric drill;
plane;
tape measure and level;
drill.

A slope for a slide can be purchased from a factory or you can make it yourself

By the way, it is not necessary to use a wooden ramp - cracks may appear on it or chips may break off, which can injure the child. You can buy plastic slides and install them on a wooden structure.

In the case of a metal structure, everything is a little more complicated. You'll need it here welding machine and Bulgarian. All seams and joints in wooden and metal structures should be carefully sanded so that the child does not accidentally get hurt during play. Metal ramps for children's slide should be painted with a special paint that will absorb sunlight and prevent the metal from heating to high temperatures.

Drawing of a wooden slide device for babies

How to build a children's slide at the dacha with your own hands

If you decide build a slide for a child on your own, you should follow a certain sequence of actions:

first of all you need to prepare construction plan. You can take a ready-made one from the Internet or draw your own. Ready drawings of a children's slide made from wood with your own hands are good because they indicate the exact proportions of the elements and the sizes of individual parts;
Referring to the diagram, it is necessary to cut the boards, slats and beams. In addition, they must be sanded so that splinters cannot get under the child’s skin. Using a plane, the beveled edges of the corners of the parts are removed, which will further increase the safety of the structure;

Wooden structures are environmentally friendly and quite easy to install

markings are carried out in the designated area. It is worth allocating a site with a reserve if you are going to build a children's slide along with it. sports complex for the dacha. Optimal size for a structure without additional extensions - 2 by 2 m;
recesses of approximately 60 cm are dug under the supports. wooden beams, the ends of which should be covered with a special waterproofing mastic. This is done in order to extend the service life of the supports. Grooves are cut into the racks into which connecting wooden boards are inserted. The elements of the resulting frame are connected to each other using bolts or self-tapping screws;

Drawing of a wooden slide for a children's playground in the garden

then the floor is installed. At building a slide at the dacha with your own hands remember: it is important that the floor is as strong as possible, so thick boards are selected for it, which are connected to each other with self-tapping screws and screwed to the frame using metal corners. If you do not want water to accumulate on the floor of the slide, you should leave small gaps between the boards, but not enough for the child to stick his finger into them;

Railings and fences – required elements designs children's slide

A ramp for children's slides is being manufactured. Its width should not exceed 80 cm. The surface of the slope is covered with linoleum, galvanized sheet or plastic. Linoleum is the cheapest option, but is easily warped and torn. The metal coating heats up noticeably in the sun and can also bend. The most reliable option is plastic slides for children's slides. Plastic does not overheat, does not rust or bend, but is more expensive than linoleum or metal coating;

Drawing of a slide structure for a children's sports complex

a ladder is being installed. The optimal size of boards for its manufacture is 20 mm. After installing the main part, the side part is installed. To do this, a board sawn at an angle of 45° is attached to the racks with screws. Then the bars are screwed to the board, onto which the steps are mounted. Photos of do-it-yourself wooden children's slides on the Internet clearly show how exactly the elements of the stairs need to be attached. After installing the steps, balusters are installed on which the railings are attached;

Photo: the sandbox can be arranged both at the base of the slide and at the end of the descent

Helpful advice! Railings must be made in any case, regardless of the height of the slide or the angle of inclination of the stairs. They serve not only for safety, but also to make it easier for the child to maintain balance when lifting.

Grooves are cut out in the side of the racks into which side walls made of plywood or fiberboard are installed. The walls can also be made of small boards or have some original look;
All protruding corners, heads of nails and screws are removed, all surfaces are carefully sanded and coated with paint or a special protective varnish.

Drawing of a children's slide for a summer residence. Overall dimensions: length - 3020 mm; width - 890 mm; height - 1800 mm. Maximum user weight - 100 kg, minimum child age - 3 years

An interesting modification of the design could be a slide - a sandbox for children. In this case, the sandbox is organized either at the base of the slide, or you can build a reservoir with sand at the end of the descent.

Materials for building a children's slide

If you are in doubt about what material to use to build a house with a slide for children or another similar structure on personal plot, you should familiarize yourself in detail with the features of buildings made of the two most popular materials - wood and metal.

Wooden children's sports complex for a summer residence with a slide

Features of a wooden slide

Wooden structures for children's playgrounds have proven themselves well several centuries ago. All children's slides made of wood with their own hands are built according to a classic layout, which includes a ladder and a ramp, a base, upper platform and protective part. In addition, often standard project add additional elements, for example, an internal labyrinth, a sandbox, additional descents and much more. Since such a design can be made quite simply, everything here depends solely on your imagination.

Photo: installation of a plastic descent – best option when constructing a slide intended for small children

One of the significant advantages of creating a wooden slide for children in the country with your own hands is the low cost of production. The material itself is relatively inexpensive, and specialized tools are also not needed to process it. In addition, building a structure from boards and timber does not require any special construction skills and abilities from you - sometimes it is enough just to strictly adhere to the diagram found on the Internet.

Another advantage of this design is its environmental safety. Wood does not cause allergies and does not emit harmful substances when heated. The only controversial point here is the paint and varnish coating of the structure, so be sure to read the instructions when purchasing varnish or paint to cover the slide.

Photo: simple design children's slide made from tree trunks

Helpful advice! The wood for the slide must be High Quality, dry and well sanded. Choose the strongest types of wood, and to increase resistance to humidity or temperature changes, the boards must be coated with a special compound.

Element to pay attention to Special attention when installing a wooden structure, this is a descent. It is best not to take risks using planed boards yourself, but to purchase factory-made material for the ramp. It can be linoleum, a sheet of stainless metal or plastic.

Photo: children's playhouse wooden with plastic slide

Features of a children's metal slide

Metal slides for children used to be in every yard and, with proper care, could last for decades. Photos of children's slides with their own hands made of metal show that in appearance they are not much different from their wooden counterpart.

A significant advantage of a metal structure is its strength. The iron structure does not require special treatment or maintenance, withstands temperature changes, high humidity, large mechanical loads. The only thing that needs to be done periodically with a metal slide is to renew the paint and make sure that the paint coating does not peel off as a result of corrosion.

Strength and durability are the main advantages of metal structures

How make a slide for children with your own hands made of metal? To do this you will need ready-made elements, a grinder and a welding machine. Particular attention should be paid to the seams, as they are potentially dangerous for the child. The quality of welding is also of fundamental importance: the higher it is, the stronger the structure will be.

Flaw iron slide– quick warming up in the sun. If you install such a structure where the sun's rays constantly fall on it, your child can easily get burned. Therefore, if you decide to build a building from metal elements, you should select a place for it in the shade or make a special one.

Photo: a metal slide with a plastic slope installed by the pool

At building a slide with your own hands it is not necessary to use only wooden or metal elements. These materials can be combined in different proportions, thus obtaining an original, reliable design.

Of course, one can always wonder where buy a children's slide for the dacha. This can be done in any specialized store or online. But remember that only a design made by yourself will satisfy all your requirements and allow you to realize your design fantasies.

Even a factory-made slide can be supplemented with independently created elements

There are a number of points that are worth considering to ensure that the design is reliable and safe:

for additional stability of the balusters, the staircase of a wooden structure should be additionally strengthened with the help of planks;
drawings, videos, photos of children's slides at the dacha with their own hands show that the grooves and slats inserted into them, when bolted together, form a light, but strong and stable structure;

At construction of a children's slide in the country the height of the structure should be carefully calculated

an excellent option for painting a structure - acrylic paint. It is safe for the child’s health and protects the tree well from various types of negative impacts and looks attractive. Acrylic is also famous for its durability and does not lose color saturation even with prolonged exposure to direct sunlight;
a convenient type of covering for use under the slide - artificial grass or rubber. This does not require special care, does not change its properties depending on the time of year or weather, and creates a safe surface under the slide that will protect the child from injury if he falls from the slide.

The surface around the slide for children should be as traumatic as possible

Plastic slide for children purchased in a store or construction market is not always the best option. Yes, you save time and effort due to construction, but a wooden or metal structure can not only cost less money, but also allow you to create a full-fledged sports complex for your child, consisting of a large number of elements. By the way, even a plastic slide for children can be supplemented with homemade elements and turned into a complex and exciting structure for games.

A high-quality and reliable slide is not only good way keep your child occupied during their stay country house, but also the opportunity to develop it physically.

Why do children love to go down the slides? An idle question. Well, it's cool, that's all. These smart adults and aunts have discovered that downhill skiing trains the vestibular apparatus, coordination of movements, teaches how to correctly assess the degree of risk and group in a fall. Many animals make smooth paths for themselves on wet clay slopes and slide down them.

You can make a children's slide with your own hands without much difficulty. You can find many slides for children to ride that their mothers built for them. There is always a place for a children's slide on a plot of any size, see fig. below. The cost of materials for a no-frills children's slide, as long as the ride is good, fits into the equivalent of $15-$20.

Parents who have some excess free time and money can practice craftsmanship and design using a sample slide for children to ride (see examples in the next photo), without risking spoiling something significant and prestigious: any indispensable foundations of the design of a children's playground there is no corner. But certain technical rules There are performances of children's play slides in the material. They are dictated by safety requirements that take into account the characteristics of the child’s body.

To get started, watch a detailed video on how to build a children's slide like those that are still in many places in kindergartens and on:

Video: building a wooden children's slide

The author is undoubtedly a knowledgeable, skillful and conscientious person. As far as construction techniques are concerned, he must be followed. But he either simply repeated the design of known samples, or, if he was guided by some regulatory documents, then outdated. Currently, the construction of children's slides is regulated by GOST R 52168-2003, taking into account modern data on some features of the child's body and psyche.

What do you need to know to ride profitably?

We are more than 3/4 water - this is common knowledge. As well as the fact that the child’s skeleton has not yet completely ossified and has not gained the elasticity of an adult. Although children are generally stronger and more resilient than adults, their skeletons are slower and worse at accepting and absorbing (damping) instantaneous loads. Previously, these features were considered separately; now – in interaction. A modern slide for children takes this into account to the fullest. Namely: a slight, but sharp push in the direction from bottom to top causes children's body a wave of compression of internal organs. This is called hydrocontusion. On a hill, hydrocontusion is negligible in absolute value. Repeated repeatedly and systematically, it gradually causes harm. A bump, bruise or abrasion can cause the whole world to roar, but they pass without a trace. Regular, completely imperceptible hydrocontusion by a child can cause a number of disorders and development and diseases of the musculoskeletal system. Plus possible anomalies of mental development: the child does not learn to correctly assess the degree of danger, risk and the degree of his endurance.

Scat

The main thing in a slide for skiing on the fifth point is its slope. GOST R 52168-2003 pays the most serious attention to its design. The slope of a modern children's slide should have a profile that completely eliminates hydrocontusion.

Excerpts from GOST R 52168-2003 regarding slope profiling are shown in the figure:

Its difference from the old ones is the obligatory presence of the final section C (brake pad, brake springboard). The sliding section Β (accelerating) must be interfaced with the braking smooth transition. Along the entire length of the slope there should be no joints of covering sheets, visible fastener heads, or other potentially traumatic areas. Since children really like to plop down with a soft place on the starting section before sliding down the slide, it is also highly desirable to pair it with the acceleration section smoothly. The ratios of the sizes of the sliding and braking areas are as follows:

B up to 1500 mm – C=300 mm for both types of slopes. Side height from 150 mm;
B from 1500 mm to 7500 mm – C from 500 mm for slopes of type 1 and from 0.3 B for slopes of type 2. Side from 250 mm;
B from 7500 mm – C from 1500 mm for slopes of type 1 and from 0.3 B for slopes of type 2. Side from 350 mm.

From slides of type 1 they slide onto a damper: into a sandbox, onto an inflatable or padded mat. In this case, section C must protrude at least 300 mm above the damper and overhang no more than 150 mm above it. Based on this, the height of the overhang of the end of the slope above the ground is calculated. From a type 2 ramp they roll down onto a lawn or soft bedding. The recommended overhang height of its end H is 50-70 mm, but not more than 120 mm. A type 1 ramp must be equipped with a side along its entire length as per the list above. For a type 2 slope, the side should extend into section C by 1/3 of its length.

Drawings of finished profiles of children's slides with extremely small and close to extremely large slopes of the sliding section are shown in Fig. (with support beams and sides); on the right, the profile line is highlighted in bold. To get a 50 degree profile from a 47 degree profile with more than enough accuracy for practice, it needs to be rotated 3 degrees clockwise.

It’s easier to slide down a steep hill, and it takes up less space, which is essential if you are designing a children’s slide for a summer cottage. For such a case, you need to make slides with an inclination of more than 40 degrees type 1, otherwise the braking section will be too long. Slides with an inclination of less than 40 degrees are made of type 2: the brake ramp, which gives the most thrill in the type 1 slides, will only spoil the fun of the type 2 slides (see also below, about the surfaces of the slides).

It is not difficult to design a slide profile of an arbitrary (within specified limits) slope specifically for your specific location. We need 3 profiles: minimum slope type 2, maximum type 1 and some middle one, with a flat section C of minimum length, so to speak, a half brake, half springboard. The profiles are drawn to scale, one above the other, so that the starting ends are spaced at equal distances from each other. Then vertical secants are constructed with the same step. The segments between the profiles are divided proportionally to the resulting angle, and the desired profile is constructed from the points, see Fig. on right. The slope angle, based on the available space, is calculated as φ=arctg(D/L), where L is the length of the downhill section minus the length of the braking section.

It remains to find somewhere a slope profile of 40 degrees with a flat section C of the shortest length. A slide for a children's playground, the drawings of which are given on the next page. Fig., has just this. The missing dimensions can be removed from the drawings; they are made according to all the rules. The entire design, which is quite complex, is not worth repeating, but the profile of the slope here is exactly what is needed.

Note: smooth connection of the beginning of the slope with the platform, if necessary. It is made using a pattern - the radius of its curvature is not critical, from 150 mm.

Platform height

By general rules TB, if a solid support under a person’s feet is above the base surface (floor, ground) above 1.7 m, then this is considered to be at a height. For an adult worker – work at height. For which an increase in salary is due. This is something that employees themselves often don’t even suspect, and even if employers know, they don’t raise the issue.

In relation to a children's slide, this means that the height of its platform should not be more than 1.7 m. However, for a country slide this is not significant; If the height is higher, it will spread over the entire area. And without hyperbole, it will significantly reduce its productive (or simply useful - for recreation) area. “No more” criterion is quite vague. If we also look at by-laws and industry regulations on this topic (GOST has the force of law), then two options emerge. The first one is that the site is solidly fenced and has a roof. There are only 2 openings in it: the entrance and the exit to the slope. Then its height can be maximum, 1.7 m. The staircase in this case is made in compliance with the rules for designing stairs in residential premises: passage width, slope, configuration of steps, etc. If any of these conditions are not met (say, there is also an opening to which the climbing frame fits), the platform should be made no higher than 1.3-1.4 m so that an adult can freely hold the child.

Note: It is advisable to make the flooring of the platform from tongue-and-groove boards, so that those who climb under it (what could we do without it?) do not have rubbish and sand falling on the firebrands.

Flooring and roofing

The smooth, slippery covering of the slope should lie entirely on a solid, hard and moderately elastic flooring. On the old slides without flooring, did you notice what looked like small dips under the cover? Each of them is hydrocontusion. Not the same, of course, as a parachutist who forgot to pull the ring, but quite sufficient to harm a child. Or just ruin the fun of riding.

Taking into account everyone modern requirements selection of materials for slippery surface small. Plywood, by the way, is not suitable: when peeling the veneer from a wooden block, the structure of the wood is seriously damaged, so plywood is not a material for external use. The best Finnish baked plywood on the slope of the hill after the first winter gives splinter after splinter. Covering options for the slope of a children's slide are as follows:

Wood impregnated with water-polymer emulsion (WPE), and on top - 3-4 layers acrylic enamel for baths or, better, 2-3 layers of yacht varnish or enamel. Yachting paint coatings roads, but are designed to withstand the abrasive effects of suspended matter in water and provide a very smooth surface, because Frictional resistance to movement is significant for small vessels. This coating will last 3-5 years until repairs are required; You won’t be able to slip on acrylic in 2-3 years, but you will get through it without difficulty, and it will need to be renewed. Wood flooring made from hard, fine-grained wood (oak, beech, hornbeam). Before painting/varnishing, it is thoroughly sanded and puttied.
Linoleum - laid on flooring sanded to the profile (see below). If the stingray is covered with film for the winter, it will last 2-4 years, depending on the climate. Therefore, instead of overlays that hide the fasteners (also see below), it is better to install MDF skirting boards, pre-impregnated with EPE and painted or varnished.
Stainless steel with a thickness of 0.25 mm. Excellently slippery, does not lose anti-friction properties over time. On a solid wooden pillow it does not overheat under the sun. Buying a solid piece of stainless steel in our time is not difficult: even in small provincial towns in a tool store they will cut it from a roll for a sweet soul. In extreme cases, you will have to wait a few days until it is delivered from the nearest warehouse metal materials. There is only one drawback: any edges are traumatic, so they must be hidden or tucked. Advice about rolled stainless steel: find out which is more affordable in your area, and adjust the width of the slope (from 750 mm) to the width of the cut.

Note: how to make a children's slide with a stainless steel slope cover with your own hands, see next. video clip:

Video: children's slide with a metal ramp (+ with a house and a swing)

How to make a ramp from wood

Tree in general excellent material, but how to make a profiled slope from ordinary boards or beams? It is impossible to steam the boards so as to bend them at home. Well, you can make a composite slope from scrap materials: scraps of boards and slats with a thickness of 20 mm or more.

How to make a children's slide from wood with a profiled slope from ordinary lumber is shown in the figure:

The dimensions of boards, slats and beams are conventionally increased for clarity. After assembling the flooring on the stringers, it is sanded into the profile with a powerful drill (at least 350 W) or an angle grinder with a flexible grinding wheel (Durex). You can make Durex yourself from a circle of thick rubber (from 6 mm) with a diameter of 400 mm. To work with Durex, you will have to remove the safety cover from the grinder, unless it is removable, of course.

Note: Under a covering made of linoleum with a lining (insulated), the flooring in the profile does not need to be sanded.

About purchased stingrays

The ramp, as we see, is the most labor-intensive part of the slide. Isn't it better then to buy ready-made? Propylene slope, slippery and durable outdoors, can be found on sale at a reasonable price.

How to choose the right ready-made slope for a children's slide is shown in Fig. below. It is better for older children to take stainless steel ones (item 1), and for the youngest (2-5 years old) - propylene ones (item 2), they are not so slippery. Make sure that the steel coating does not protrude anywhere (item 3), sharp edges are dangerous. Slopes with railings (pos. 4) are even more dangerous. What child doesn't flail his arms while he's rolling? What if your hand hits the railing during the crash?

Slopes with sharp breaks (pos. 5) and without a braking section - hydrocontusion after hydrocontusion. In slopes with inserts (pos. 6) and in general with joints on the coating (pos. 6), a traumatic ledge will inevitably form. Slopes with a threshold above 200 mm (item 7) are also produced by manufacturers high level. There is no obvious deception here, there is an “allowed” commercial trick: such slopes are designed for use with inflatable mats for outdoor use. Mats are sold optionally, i.e. separately. Price? Reasonable, economically justified: a little more expensive than the entire children's play corner.

But the spiral (very cool, of course) slide at pos. 8 is a real monster. The slope of a spiral slide must certainly be grooved, once. Second, in this case, the outer side at the bend needs to be at least twice as high, otherwise even a very calm child can fly off the slope of this slide at the turn.

Design examples

Good owners never have too much space in their dacha or garden, and this is where a corner slide comes in handy. But don’t squeeze it into the corner of the fence: the distance from the slide to any obstacle must be at least 1.3 m!

Drawings of the corner children's slide and its upper platform are given on the following. rice. Of course, it is better to make the slope profiled. In the same way, as a platform, you can build a sandbox for landing; then the length of the boards for it needs to be 1800 mm. The slide platform is supported by 4 pillars 150x150 at its inner corners.

The pillars do not need to be concreted. It is enough to scald their lower ends with hot bitumen to a height of 750-800 mm, sprinkle them with sand while still hot, wrap them in roofing felt and dig them in to a depth of 60 cm or more. In the pits you need cushions made of 15 cm of sand + the same amount of crushed stone, i.e. pit depth from 900 mm.

For scalding, the ends of the beams are immersed in almost boiling bitumen. Slowly, otherwise hot splashes will fly! Then they wait until the bitumen around the tree stops hissing and bubbling. This means that air and moisture are forced out of the wood. After this, the beams are kept in bitumen for at least 10-15 minutes so that it saturates all the pores. After installing the pillars in the pits, they are covered 3/4 of the depth with crushed stone in layers, 15 cm each, with a tamper and topped up with excavated soil with a height of 15-20 cm. Wooden non-foundation buildings on such supports last for 40-70 years or more.

In Canada, whose climate is similar to Russia’s, only even wetter, top platforms for children’s slides are common, which do not require excavation for installation, see fig. below. For proper rigidity and reliability of the entire structure, it is necessary, firstly, that the upper platform itself be of a box-shaped structure. That is, there may not be a roof, but balusters (baluster) and stiffening connections from the rear (stringer) are required. Secondly, the ladder legs (ladder legs) must be attached to the strapping bars with rigid one-piece units (leg brace), consisting of persistent jibs and attached earrings on the outside.

It is better, of course, to fix the entire structure on the ground not with pegs, but with L-shaped anchors made of reinforcing bars. The anchors are driven to a depth of 60 cm. In order for the ladder support brace, exposed to both soil and atmospheric destructive factors, to last for a long time, they must be protected from rotting especially carefully. For example, the same as the heels of a fence for a front garden, which is also installed directly on the ground.

The development of the idea of a slide for children to ride, installed on the ground without excavation, are the samples shown in the following. rice. They use the rigidity of not only the triangle and the box, but also the so-called. biplane box. This gives a large supporting area, so such slides do not need to be attached to the ground at all, and the entire material is a 150x24 board. Second interesting feature– sides of slopes of decreasing height along the slope. You won’t fall off the top, but you’ll roll around - wave your arms and scream from your heart. Ready-made factory products of this type are available for sale; they are brought and simply placed where the owners indicate.

What if it’s a splash instead of a smack?

Translated into adults: if there is a swimming pool at the dacha or site with a depth of 60 cm or more. The slope of the slide for sliding into the water should have a curvature profile that decreases towards the end, and the finishing section C should also have a special profile and hang over the water surface by at least 400 mm. A splash instead of a splash is a delight to the skies and higher. Therefore, we conclude the publication with drawings of a slide for sliding into the water, see fig.

Mandatory elements of the attraction complex on summer cottage There is a sandbox, a swing and, of course, a slide, which even older children will enjoy riding on. Most of them can be made independently, saving on the expensive purchase of ready-made structures. For example, constructing a children's slide with your own hands is quite simple, using available materials.

Advantages and disadvantages of different types of slides

In order to choose the material from which the children's slide will be made, you need to carefully read each of them, weighing all the pros and cons. The most popular are:

tree;
metal.

Even though they have a similar design, the manufacturing process is still different. The reason for this is the characteristics of the materials.

Each of these slides for children is built according to a standard layout, which includes:

stairs;
descent;
base;
upper platform;
mandatory protective component.

In addition, the classic design is often supplemented with all sorts of internal labyrinths, sandboxes, additional descents - here everything depends only on your imagination.

Advantages:

Low financial costs. Since wood is relatively inexpensive, and specialized tools are not needed to process it.
Ease of manufacture. Building a slide from wooden planks and blocks does not require you to have any special construction abilities or skills. Often it is enough to adhere to the scheme according to which the structure is made.
Minimum tools. To construct a slide you will not need a large number of various devices.
Environmental Safety. Wood, as a rule, not only does not cause allergies, but also does not emit toxic substances when heated.
Any place to install the slide. Unlike a metal structure, a wooden attraction can be placed in any convenient place on the site, since in the scorching sun the wood will not heat up and will not burn little fidgets.

Flaws:

Susceptibility to rotting. Wood is a material that requires treatment with special protective agents and varnish. If this is not done, then the slide begins to rot and dry out under the influence of external factors.
Descent deformation. This happens due to exposure to rain and sunlight.

When installing a wooden structure, special attention should be paid to the slope. To cover it, it is best to purchase factory-made material, for example, linoleum or plastic. The latter is more expensive, but more reliable and safer.

If desired, it is very easy to remake a wooden slide, for example, turn it into a pirate ship.

Metal constructions

Just a few years ago, such slides decorated almost every yard. With proper care, they can last a very long time.

There are practically no significant differences between a wooden and a metal slide, except that an iron structure will require pouring a foundation. This design consists of:

small sites;
descent;
ladders made of pipes.

Advantages:

Structural strength. The advantage of a metal structure is that it does not require special care, it can withstand temperature changes, rain and high humidity, as well as heavy loads.
Reliability. It rarely happens that any part of such a design becomes loose or comes off.

Flaws:

Difficult to install. To install a metal slide you will need a welding machine and the ability to use it. Moreover, you will need knowledge of metal working technology.
Heats up quickly in the sun. Iron is subject to rapid rise and fall in surface temperature depending on the time of year. If you install the slide in a place where the sun shines brightly, your child can easily get burned while playing. To avoid this, it is recommended to install the structure in a shaded place or hide it under a special canopy. It is possible to combine a metal base with a plastic slope.
Loss of interest in the child. It is almost impossible to decorate a metal slide with anything, which means that such an attraction can bore your child.

After familiarizing yourself with the advantages and disadvantages of each manufacturing material, you can confidently make a choice. It is not necessary to use only metal or wood; you have the right to combine them, resulting in an original, interesting and durable structure.

Photo gallery: different slide designs

Slides can be part of an entire entertainment complex Slides can be expanded various elements Bright wooden slide kids will definitely like it A high-quality and reliable slide will bring a lot of fun to children and their parents
For children of any age, fun on the slide will be happiness A reliable slide is the key to safe games Wood is the best option for non-professional welders Metal slides are considered the most durable structures

Requirements for a children's slide

It is worth understanding that when installing a slide from any material, certain requirements must be observed:

Preparatory stage

The success of the work depends on careful preparation.

Choosing material for construction at the dacha

Wood can be called the most optimal and reliable option from which you can build unusual and original structures. It will be a godsend for people who are not directly involved in construction and repair.

When installing an iron slide, unprofessional welders and assemblers of metal structures can injure themselves or damage the raw materials, since this is a delicate material that can become deformed when heated and welding. In addition, to manufacture such products you will definitely need welding equipment.

Children's slides made of wood combine ease of use and high safety. Moreover, they are the easiest to manufacture and install.

Sizing and drawing

Work must begin with drawing up a design drawing. Be sure to decide whether there will be a slide with a house or whether it will be a classic option. Draw a diagram of it indicating all dimensions. This will allow you to calculate the amount of material. Norm:

for children from 2 to 5 years old, the slide should be made up to 1.5 m high;
from 5 to 11 years it is recommended to install a structure with a height of 2.5 to 3.5 m;
over 11 - above 3.5 m.

List of materials and tools

The construction of the structure should begin with the choice of wood. It is preferable to use coniferous species. In order to build a reliable, beautiful and comfortable wooden slide for children, you will need the following materials:

8 boards (recommended dimensions - 5x14x60 cm);
4 thick beams 0.6 m long;
1 beam 0.8 m long;
several sheets of plywood (150x150x12 cm);
2 round wooden profiles (30x120 cm).

List of required tools:

electric or mechanical wood saw;
hammer;
hand or electric drill;
plane;
tape measure and level;
drill.

Step-by-step guide to creating a children's slide with a ladder with your own hands

All work takes place in several stages:

How to cover the base, walls, platform and slope of the slide for better sliding and decoration

At the end of all work, the slide must be coated with varnish or a coloring emulsion. It is also recommended to treat wood and plywood by special means, otherwise, under the influence of moisture, their service life will sharply decrease.

The slope can additionally be covered with linoleum, which will provide better glide.

You can decorate the slide with your children. They will definitely enjoy this process.

Photo gallery: external finishing of the structure

Coating with varnish and special emulsions ensures a long life for the slide Wooden slides provide exciting games A slide made of wood, which is coated with emulsions and special agents, will allow children to play safely In addition to varnish, slides can be coated with any emulsions, thereby giving them bright shade Multi-colored options will delight kids Upon completion of all work, you will have an excellent attraction for children that will meet all safety requirements

Video: how to make a slide for a child out of wood

The key to a successful and fun time is a high-quality and reliable slide. It is a way to keep your child busy with an exciting activity and develop his physical skills. And as the baby grows up, it will be possible to complete the design, improve it, which can encourage your fidget to healthy image life.

Setting up a playground is impossible without a slide. But you need to choose the design very carefully and take into account all the nuances. This means safety, comfort, and ease of making it yourself.

Kinds

Speaking about the types of children's slides, we must first distinguish two types: garden and located in the house. Most often, home structures are placed in the bedroom. They can be made from randomly selected materials, even plywood or particle boards. This is unacceptable on the street - the adverse meteorological influences there are too strong. But the basic approaches to design remain unchanged.

The difference may be due to the materials used to make the slide. For it they use:

tree;
metal.

ease of assembly;
minimum occupied territory;
possibility of obtaining various forms;
convenience and safety;
seasonal versatility.

Plastic allows you to make slopes in the form of a spiral, pipe or wave. Excellent heat capacity plastic stingray allows it not to overheat in the summer, and also maintain a comfortable temperature in the winter. The work is very simple, you just need to assemble the parts in accordance with the instructions. However, plastic is fragile, especially if we talk about cheap Chinese samples. It doesn't last long enough.

Often on site nearby apartment buildings you can see metal slides. They are very durable and serve long time. Even with active use, the attraction will work enough for several generations to use it. You can make a structure with different heights and with unequal lengths of descent.

However, before choosing such a structure for your yard, you need to take into account its weaknesses.

Metal conducts heat too well. In hot weather, it gets very hot, and when cold weather sets in, the skaters easily freeze. This can lead to bad health consequences, even if they are not noticed in the heat of the game. You also need to remember that metal requires maintenance. And if the ramp is made of steel, it may corrode.

Wood is attractive for many reasons. It is safe in environmental and sanitary terms. Wooden structures are relatively lightweight and can be placed in any location. Weather conditions do not prevent their use. But we must understand that Even the best wood can become deformed from dampness and temperature changes.

Special treatment is carried out for protection. However, it complicates and increases the cost of the construction process. In addition, it is necessary to carefully select impregnation compositions, since not all of them are safe enough. But a wooden slide can be easily repaired with your own hands. And during the construction stage you will not need to use a welding machine.

The large area occupied by the slide (especially together with the descent) requires a more thoughtful approach to organizing this element of the playground. You cannot limit yourself to choosing the right material. Often the slide is complemented by a house. Not only does it become another place to play, but it also helps provide shelter from the rain in summer months. It is also worth mentioning that the types of slides differ both in the presence of the house and in the size of the structure.

Drawings and dimensions

In order to properly build a slide for children on a summer cottage, it is necessary to draw up drawings and diagrams. If the slope profile found on the Internet does not suit you, you need to turn it clockwise (to increase) or counterclockwise (to decrease) the angle. The steeper the slope, the more enjoyable it will be for children. In addition, such a design will take up less space, which is especially important in the country.

But when the slope of the slide is tilted by more than 40 degrees, careful calculations must be made so that the braking section does not turn out to be excessively long.

Typically profiles are drawn to the same scale, from bottom to top. At the same time, they try to ensure that the distances between the starting points coincide. After this, vertical secant lines are prepared, between which there should also be an identical distance. The angle of the slope is determined by how large the free space is.

If in the courtyard of the house near the descent there will be a wall, a pool or other dangerous places, you need to plan to build the steepest slide possible.

When drawing up drawings, it is necessary to take into account not only the accessible territory, but also the age of the children. So, if the design is designed for a category of 3-7 years, you can make a playing surface at a height of over 2 m. But in this case you will have to make barriers from metal, the height of which will be at least 0.7 m. If children of any age can use the slide, the openings of the fences can be a maximum of 0.5 m. In this case, the height of free fall should be limited to 2 m.

When a fall from the upper platform is likely, it is necessary to provide for the laying out of an impact-absorbing coating during the design. Drawings often do not indicate supporting structures. And also there may be no other deepening elements. The form should be as simple as possible, since it is difficult to build a structure with a sophisticated configuration. The drawing of a slide for the street should be made in such an orientation that the descent is not directed towards the roadway.

Design

At an early age, children's imagination does most of the work. It is able to “colorize” a seemingly unremarkable element on the site, presenting it as a fairy-tale space. But it is quite appropriate for some adults to want to help the imagination, to push it in a strictly defined direction. And if it is difficult to diversify the slope, then the ascent can be presented much more interestingly than a simple staircase. Excellent solutions this kind can be:

slide in the form of a “tractor”;
a house on a tree;
"locomotive".

How to do it yourself?

On the Internet you can easily find many schemes for arranging a children's slide. But you should seriously pay attention only to such drawings and drawings that show the barriers in detail. Children of any age play with abandon and lose their sense of reality. Therefore, both fences and railings must be present. Special attention should be paid to the materials from which the slide as a whole and even its minor parts are constructed.

There are two main requirements: sanitary safety and minimal risk of fire. All wooden and metal constructions must be sanded to minimize the risk of injury. When thinking about a future structure and constructing it, you need to exclude any slotted partitions and gaps. When playing, children do not watch where they put their fingers or even their heads. It is useful to imagine the slide through the eyes of a child, and then it will become clear where dangers may be hiding.

The step-by-step design of sports equipment begins with the preparation of the descent. It is made from boards that match in length and width. The wood is carefully sanded to ensure a safe descent. To connect the boards, bars are used, placed from below. The next step is to attach the side parts of the structure to the descent.

In order not to carefully calculate all the proportions, you can simply repeat standard sizes factory slides. It is 1.3 m in height at an inclination of 55 degrees. The boards of the side parts are selected and placed so that the ends are at the top of the site. They function as handrails that you can hold on to before descending. The sides are secured on both sides with self-tapping screws so that they hold onto the base of the descent.

Important: the side parts should be thoroughly processed. All sharp corners are cut off and even sanded with sandpaper. To spend less time and effort, you can simply take a grinder with a grinding disc. Next you need to do the marking. At this point you will need a garden auger.

Recesses in the ground obtained with its help are needed for installing timber. Note: the bottom of this beam should be lubricated with mastic. Now the places where it was placed are being concreted. Only this solution ensures the reliability and stability of the structure. It is recommended to mix the mortar using M500 cement in standard proportions.

Grooves are cut in the upper part of the beams with a saw. They are needed to install the trim strips. The parts are connected using self-tapping screws. The slats solve two problems at once: they increase rigidity and ensure the safety of children. Now you need to attach a couple of wooden crossbars to the frame.

A ladder is attached to them on one side and a prepared descent on the other. When this work is completed, it is necessary to build a wooden floor. When making it, boards are laid, attaching them with self-tapping screws.

Important: boards cannot be placed closely. The gaps should be such that there is no risk of injury, but water can drain freely.

If maximum strength is needed, the joints of wooden parts are reinforced with steel corners. It is recommended to make the slide twice as long as it is tall. When choosing a site, you need to make sure that it does not end up in a lowland. When it rains for a long time, a “swamp” will form there. All wooden and plastic parts must be impregnated with fire retardants.

But the construction of a wooden slide can happen differently. Alternative scheme implies that they will first remove all the soil and level the excavation. This is necessary if there is fertile land there - then it will not be empty and will be useful somewhere else. Next, the site is covered with sand and after a while, when it settles, the entire area is compacted. This time should not be wasted, you can:

prepare wood;
dry it;
cut according to the drawing;
sand;
impregnate with protective components.

The steps, handrails, railings and boards that will be needed to build the “tunnel” are painted twice with enamel. They need to be sanded between paintings. On this preparatory stage ends. The time has come to build the foundation: reinforcement is placed in the holes prepared using a garden auger. It will certainly be verified according to the building level.

When the reinforcement is placed, it is immediately concreted, and the corners are welded on top. The pillars that will be placed at the base must be sawed in certain places. These recesses will allow you to fix the timber at the corners with self-tapping screws. Next, the pillars are connected to each other using jibs. The staircase is made like this: stringers are attached, and then steps are placed on top of them.

But the ladder cannot be used normally if it is not supplemented with a launching pad. When this work is completed, it is necessary to prepare the base of the descent (it is made of timber). A steel curved profile for the slope is installed. A plywood shield is placed on top of the base under the slope. A sheet of iron is nailed onto this shield.

The outer edges of the sheet are folded and secured to the profile. Otherwise, injuries are inevitable. Now you can cut gaps in the boards and wrap the edges of the sheet there. A boardwalk is being prepared under the ramp. The sides are covered with plywood. Now you can:

put up the sides;
complement the stairs with railings;
build hipped roof, cover it on top with plywood.

sheet of plastic;
linoleum;
galvanized steel 0.05 cm thick.

It is not advisable to use laminate for slopes. Under constant load or simply upon contact with water, it is easily deformed. And here are some more recommendations:

You can increase the protection of wood from moisture by polishing it with wax;
for covering a wooden slide Oil paint much worse acrylic compositions and varnish;
you can’t place a slide near poisonous plants and honey plants;
you must immediately ensure that there are no pipes or electrical appliances nearby;
You cannot orient the slope towards the roadway, fence or main wall.

Beautiful examples

It would take a long time to list the rules for building slides and study the nuances. But it is much better to take the initiative and focus on ready-made design ideas. The photo below shows a simple light-colored slide built almost entirely from wood. Only the surface of the slope is laid out sheet iron. At the same time, the protective sides are completely wooden. Contrary to the fears of some people, this decision does not look sad at all.

But you can also make a multi-colored colorful design, even complemented by a rather long transition between ascent and descent. A couple of tent buildings provide shelter from not too heavy rain. There is an even simpler option, in which the entire surface is made of wood. This design should be chosen when you need only functionality and not brightness. appearance.

To learn how to make a slide with your own hands in one day, see below.

Summer residents who have kids need a children's slide, and the easiest way is to make it yourself. You can buy it already ready-made option, which only needs to be installed in the right place, but for various reasons people may not want to purchase a factory-made product. And in this case, a wooden slide is the best option to create, since it can be made independently and without high costs.

From the place where it will be installed new item entertainment depends on its appearance, dimensions and material required for manufacturing. There are only two location options:

In the sports room or in the children's room, if you have them.
On the street.

Slide in the nursery

Outdoor slide

A small children's wooden slide located indoors can be made of plywood, chipboard, laminate or other materials. The wide selection of components for manufacturing is due to stable indoor weather conditions: there are no temperature changes or wind, and humidity is normal.

Outdoor models will require significantly more space; the materials used are thick wood that can withstand various weather conditions. The manufacturing process is the same in both versions, the only difference is in the size of the elements.

Outdoor slides can be found at many children's centers in the middle of cities. As a rule, they are made of metal or plastic, since these are the most durable and strong materials that are unpretentious to adverse weather conditions.

Wooden slide in the city

Slide in the yard of the dacha

Wooden slide

Wooden complex with a slide

A slide made of wood will not harm a young body, since wood is an environmentally friendly product and does not contain harmful chemicals, unlike plastic. This product is lightweight compared to metal counterparts and can be assembled quickly. It does not require a welding machine or special connecting elements.

Among the disadvantages, one can take into account the low durability due to the process of decay of wood fiber. With this balance of positive and negative properties, many people prefer to make wooden slides for children. Absolutely anyone can make such a product without the help of professional carpenters.

The process of creating a slide will be discussed using a small model as an example. All creation and installation steps are the same for most options.

Three-dimensional visualization with exact dimensions and shapes always helps the designer to create the highest quality slide and roughly imagine what the end result should be.

On initial stage To create a figurative idea of the project, the designer must pay special attention to the following points:

Independence of the person playing.

If the child is under 3-4 years old, then the slide should provide a convenient descent so that parents can help the children slide down and climb back up.

Growth parameters.

These indicators will help create a product with the most comfortable dimensions of the elements (steps, railings, slopes, handrails, etc.) of a new piece of entertainment.

Planned location.

It is necessary to take into account the peculiarities of finding a new structure. There must be free space at the construction site to ensure comfortable movement while using the slide.

Steepness of slopes and turns.

To keep an older child interested, you can create various dips and twists on the slope, but you need to take into account the angle of inclination of the sliding surface so that the baby does not damage the spine and other organs while having fun.

Individual ideas from junior assistants.

Since the slide is created for children, the wishes of the customers – children – must be taken into account.

After taking into account all additional factors, you can draw up a drawing, or download previously invented options, making individual adjustments to them.

Since the slide is for children, we need to take into account the wishes of the customers – children.

For example, for a supporting structure it is advisable to use beams with dimensions of 10x10x150 cm. In most cases, 4 support pillars are sufficient. Self-tapping screws or nails are used to fasten the elements.

The table shows examples of material sizes for a small slide.

B – timber, D – board

As an option, you can additionally equip the bottom of the upper platform with a drawer or handbag. You can store various toys, pillows, etc. in additional compartments.

All wooden elements must be processed with a plane and saw until required sizes, then sand with sandpaper or an electric sander. The support beams must be additionally treated with resin or waterproofing mastic. This is required to prevent the rotting process.

Wooden elements need to be processed with a plane

Waterproofing mastic

Preparing the installation site

Any do-it-yourself slide for children in the country requires a certain area for placement. Before installing a new entertainment item:

The territory on which it will be located must be leveled:
mark a square for the base supports of at least 50*50 cm;
dig 4 holes (60 cm or more) at the corners of the square.

Compact the area for placing the slide with crushed stone

Mounting of supporting structures

Pre-prepared pillars are installed with the bottom side (must be treated with resin) in the pits. Next, the remaining space in the recess is filled with concrete. After it hardens, further work is carried out.

To protect the supporting structures from loosening, all pillars are additionally connected by stiffening ribs. For this:

make a groove 2 cm deep and 10 cm wide in the supporting pillars;
insert boards measuring 2*10*50 cm into the grooves if you have chosen a 50*50 square as your base.

If the size is different, the length of the ribs must correspond to it

The parts are connected using self-tapping screws and self-tapping screws, this allows you to achieve the highest quality coupling. Instead of installing supports in the pits, you can use ties. As a rule, only small slides for children under 3 years old are designed to be carried from place to place.

The parts are connected using self-tapping screws

Remember! Portable and indoor models are not equipped with a fixed support.

Creating a floor covering on the upper platform

From 2 to 4 beams are mounted on the supporting pillars; they will perform two functions on the upper platform: load-bearing and stiffening ribs. Boards are placed on top of these elements, be sure to leave a gap of 0.5 mm between them. This is required to allow water to flow freely to the ground during rain.

For aesthetics, you can fasten (screw, glue) strips or pieces of laminate left after repairs onto the boards. It will be beautiful and modern. Plywood should not be used for these purposes. It will absorb water very quickly, swell and warp.

Descent equipment

The main element of the slide is the ramp. It should be slippery and equipped with additional sides so that the child does not fall out while descending from a hill. If you have a purchased descent, you just need to place it on the upper platform and secure it.

Assembly steps:

To begin with, the boards are installed from the top platform to the ground. The upper part of the pitched boards is sawn off at 30-45 degrees to ensure slope.
For fixation, it is recommended to make recesses in the descent boards to the size of the lower bar and place them so that it fits into the grooves.
Then you need to secure boards across the slope that will hold the sliding surface.
The next step is to install the protective edges. The bottom corner of the board is sawed off so that it becomes parallel to the ground.
Next, a small continuation of the slope parallel to the soil is made (bend). This is necessary so that the children playing do not hit solid ground and smoothly rolled to the end of the sliding surface.

Creating a Descent Cover

After the installation of the pitched boards is completed, they need to be sanded again to remove nicks and irregularities. Next, the boards are painted and covered with a protective hard varnish.

Many other materials can also provide a slippery descent surface:

any floor coverings, for example, linoleum;
sheet metals (thin steel, tin);
plastics.

Linoleum

Sheet metals

Plastic

The last option is the most slippery, but has a high cost compared to previous analogues.

You can use a laminated coating. But it is not recommended to use it if your base is poorly made, since the laminate will quickly become unusable due to deformation under the weight of children.

Mounting must be done carefully. At the end of the work, the sliding surface should be free of irregularities, jags and protruding elements, as this can lead to a splinter or injury to the child’s spine during descent.

To avoid such troubles, the places of all fastenings and sharp protrusions are ground off, and the wooden elements are covered with a protective layer of varnish.

At the end, the sides (10-20 cm high) from treated and varnished boards are nailed.

Don't forget to nail the sides

Creation of a staircase and its installation

To easily climb the hill you need to make a good ladder. It is most convenient to use boards as steps, but, as an option, beams or trimmings of logs are suitable

For marking and assembly:

place one of the boards (stringers) intended for the stairs in its place on the hill with its edge to the ground and cut it from the bottom so that it rests firmly on the ground;
mark the places for the steps, leaving 20 - 30 cm between the marks;
draw lines so that they are parallel to the ground;
then place two boards parallel to each other and make marks on the second stringer;
then create grooves and insert steps into them;
fasten it all with self-tapping screws
After assembly, install the ladder onto the slide.

For reliable support so that the product does not go into the ground, nail a board treated with resin from below. You can concrete this place or install stringers on the bricks.

Installation of additional fencing and decoration of the structure

The main structure of the slide is ready, it can already be used, but to ensure the safety of small children, it is recommended to additionally make railings on the upper platform and stairs.

All that remains is to give the new building a beautiful appearance. You can decorate the wooden elements. If you wish, you can equip the upper platform with carved elements (stars, bears, etc.).

For construction similar structure It may take less than two days if all materials are prepared in advance.